quadcopter

Hiya Guys, I am brand new here and even worse a rookie with the Bugs 3..... I have just taken delivery of mine today. I am wanting more batteries and have already seen that people do not rate the charger that comes with the Bugs 3. So a very simple question.... What charger and battery...

Hi I've been researching for a while regarding my first quadcopter build and I was looking to get some advice from the forums. I'm planning a 450 frame with Emax MT2213 (935Kv) motors and 8" props. I was going to pick up the Anniversary Special Edition Racerstar REV35 35A for £20 from banggood...

Hi all, I am pretty new on this hobby and I have no any quad on my hand for now. I am collecting my pieces to make a quad. However, I cannot overcome some hardware issues. I want to process images. But I don't know which control cards should be used for this mission except Raspberry Pi. If...

Hello all, Overall I'm a newb when it comes to building quadcopter. About half a year ago I bought the eachine wizard x220 and now I'm getting back into some quad flying. Back when I bought it i plugged in the battery without the antenna screwed in so I'm pretty sure the transmitter is broken...

I am building my first quadcopter, I have a lot of little cheap ones I have been flying and I really want to do an fpv quadcopter. I 3d printed a couple of 450 frames, I know most fpv are the smaller frames and if I am swayed I will go with the alien CB frame. I am trying to find a FAST motor...

I get this online newsletter called UAV Coach. In it was an article regarding the future of Hydrogen Fuel Cell Powered Quadcopters. One in particular is called the NARWHAL 2. I am including the URL Link regarding the article...

I have not been able to get telemetry to work on my SPF3 flight controlleer and my spectrum 4649t receiver. Currently i have the tx and rx tied together on the 4649t using Sbus on Uart2 of the flight controller. I have supplied ground and +5v from PDB to receiver. I cannot get any telemetry data...

I am a software engineer and don't have much knowledge of mechanics. I want to build a quadcopter that can lift about the wieght of a person say 100 kgs. I am thinking of to use a 125cc bike engine for power and gearbox for related speed change requirements. So the total weight of the drone...

Hello, I don't know which motor I have to take for my new Quadcopter. I want that my Quadcopter is relative stable (for recordings), but also response relative fast? I have a 450mm frame. I often read that the T-Motor F40 Pro II are very good motor? Many thanks

New WiFi RC mini Drone with 2.0 MP HD camera For sale Brand: Gleemax Price: $43.99 Color : Black Frequency : 2.4G Channel : 4CH Gyro: 6 Axis Camera : 2.0MP HD WIFI Motor Type : Brush Motor Material : Electronic Components, Plastic Control Distance : About 50m Battery : 3.7V 600mAh Lipo...

Hello I am beginning to develop quadcopter,and interested to use cc3d as it's cheap.Please suggest on the use any cons to consider,any better alternatives.Also plz guide if any good guide to build the quad with minimal features

Hi everyone, I'm new to this forum, and couldn't really find what I need since there are a lot of threads. I will get straight to the questions. Recently, me and my cousin built a quadcopter for school project using the VQ250 tilt rotor kit (from Vector Quads) using PX4 2.4.8 with the same...

hi everyone i am new to the hobby and i managed to build a full quadcopter by following the very well known $99 dollar quad from uavfutures. ive been try to fix this one issue of my quad being very sensitive even at 10%-15% throttle or less straight after takeoff. this problem i believe is to...

Hey everyone!!! I bought a packaged bnf quadcopter set from my local hobby store and I have lost motivation setting it up. I have done the frame assembly but the electronics are quite intimidating. It came with an unknown flight controller that I have never heard of (hobby people super m/r...

Always wanted to make a baby hawk vid so here it is check it out tell me what you think !!!!

hey, i want to build a quadcopter fpv and i want full calculation for parameters like motor kv esc mah max amps props size and battery size If can someone help me in this i dont want to use any website for calculations i want to do it by myself cause its a project for college i want to...

Hi all, Today I put together my first quadcopter, and since all was working well I thought i'd try installing a servoless payload release mechanism: Currently everything lights up but the payload release mechanism won't work when I trigger it on my radio. It definitely is receiving a signal...

Hi, I got my first Quadcopter a week ago, a Hubsan X4 mini quadcopter I really thought i was ready for the outdoors, took to the biggest field i could find and took it for a spin at about head height first - all good Then this happens: (lets see how high this thing can go) Took it up so high...

Hi Guys, Just returned from Colombia, what a country! Really magnificent. I had the pleaser to have my little spark with me for 22 days. Let me know what you think of it! :-)

I've just purchased the Flysky FS-i6 Tx/Rx combo and want a quadcopter kit to use with it, but WITHOUT Tx and Rx. Can anyone recommend a good, not too expensive ($30 - $80) kit that has everything - frame, motors, props, perhaps battery, NO FPV and NO Tx/Rx?