help

So I want a relatively cheap quad kit that I have to build. I don't want a RTF because I want to be able to make modifications to it when parts break. I came upon this and it almost seems too good to be true. http://www.miniquadbros.com/products/miniquadkit It's sold by miniquadbros and...

I have had a few drone in the past. I have had a very small one that was very cheap and broke, I then got a bigger drone, but is was also very very cheap so it broke too. I want a nice drone that i can have lots of fun with, and that can take the abuse of me. I would like to get into FPV also...

My first build is a 250 with a CC3D flight controller and a FS-t6 transmitter/corresponding receiver. I have been able to successfully calibrate the quad using the libre pilot software. However once i get to the transmitter setup wizard i cant successfully setup the transmitter. The software...

Today while i was looking at my Eachine 250 racer quadcopter i decided to try my other camera on it. (Standard is the 1000tvl, i wanted to try my 700tvl because the low light mode on the 1000tvl caused bad light glares when flying in the evevening) the plug ins on the camera were the exact same...

I have tried everything to get my naze32 V6 to hookup with my FS-IA6. something is wrong and i would just like to come over to your house and get thing working. i live in Denton, TX and i can come to you. if you can help me. i am tiered of watching youtube.

So I recently built a quad and since I first started up the motors I noticed the back left motor stops almost instantly when I kill the throttle. To the touch it seems as though the magnets are a tiny bit stronger but it still allows me to spin it freely. I want to know if there is a simple fix...

Hi, I recently bought the Kaideng k70c from bang good, i took it out on its first flight and the motors just cut off mid flight and it crashed to the ground, it did that 3 times. Please can you help me to fix this problem, its very frustrating.

Hi guys, I need some help. I have built my 2nd quad, its a Diatone 200. The quad is fully built and care has been taken to ensure the soldering in clean and everything very well insulated. I have used spaces and electrical tape to insulate the board from the frame and heat shrink for the...

Hello - I am pretty new to building my own quads. I have a X9D Radio along with a X8R7-II Receiver on a home built quad. The Flight controller is a NAZE32 (something). I use baseflight configurator. I do NOT have a GPS unit on this quad (YET - that is another part of this question). To get a...

So I went to fly yesterday, prior everything worked like a charm. Noticed my controls were acting a bit odd on first battery but i brushed it off as user error. When I plugged in my second battery the Naze32 gave me the 3 blink indicator that it connected to my transmitter and then continues to...

So I've got a new build I just finished putting together. The Title kind of says it all. When the copter is tilted in a direction it wants to correct back to level, but it is correcting in the way it was tilted. I don't think its over correcting, it's just correcting the wrong way. Example...

Title says just about says it all. I have litterally no idea what to do with these loop times..... Do they change for different ESCs? Do they change for flight board? Do they change for motors? Jesus please help x-x (Using cleanflight+Naze32 if that matters)

Im fairly new to the multirotor scene but Ive been through the stages of buying more advanced models and found myself at the Eachine 250 with the Full FPV package. This quad was beyond my expectations and really fun to fly (especially after the tune,) but most importantly it opened up my eyes to...

I'm using a CC3D board with 30AMP Afro Simonk ESC's and Sunny Sky motors. In the setup wizard what settings do I use PWM, PPM, OneShot, and have no idea what any of those stand for. I'm using a T-FHSS 8-channel Futaba Receiver. Every time I go through the setup wizard and plug in the battery the...

This is my first build, I fallowed a guide on how to build it on youtube, and my friend suggested that I get the turnigy 9x, because he has been using it and loves it. my problem is that I just got everything put together and wired up, but now I am having trouble binding the D4R2 to the stock...

Hi I am looking to purchase a drone for exploring underground inaccessible(un-supported) areas of a operating mine site. There are obviously many limiting factors to get a drone running compared to flying in open spaces like; No GPS Effectively total darkness. No retrieval possible if drone...

Making a quad, first of all ill use 4 23oo kV motors, and my esc is 12 A and it says its for 2-4S LiPo batteries, if i want flight time to be around 20 minutes, which battery should I go with? Also another thing, im afraid ill drain the lipos too much, do the remote control transmitters usually...

Hello so I think im having problems with connections between my tx and rx for my quadcopter. Its a turnigy tgy-i6 and tgy-ia6 receiver. Basically the rx signal drops to zero and sometimes disappears off the screen on the tx at only a few meters distance but the quadcopter still responds to...

Hello, Im currently in the part choosing stage of building a 250 fpv racing (fun racing not competitive) quadcopter. Iv already built a 500mm quadcopter so I know the basics but I'm stuck on what ESC I should get for my 250. I have chosen the Emax Mt2204 II 2300Kv Cooling series motor. I will be...

Hi there, I'll try and keep things simple. I bought a Fatshark Teleporter V3 RTF kit, and recently broke the Fatshark VTX. (Snapped the SMA Antenna port off of the circuit board badly enough to not be able to re-solder it) So I bought a 25mW micro VTX and have wired it in as I saw fit. My...