help

Hey I was just curious if anyone knows a setup that would fit on a blade nano qx 3d for fpv that the quad could actually lift? I would love to get into fpv but have no idea what camera/transmitter would be small enough for that size of a quad. thank you!

So iv crashed my quadcopter many times, however the last two times have been the exact same but i cant figure out the cause. I suspect its a possible faulty esc. Im using 20A Afro ESC. Both times i was flying for longer than usual, 10min<. Both times I was flying aggressively during the flight...

Hey All, So i'm a complete newbie to this site and the whole quadcopter hobby, it's been quite the experience so far!!. After tons of research and Youtube Videos I thought I could build my very first FPV250 quadcopter without any hassles - but of course nothing goes smoothly . After blowing two...

Hi I was just wondering if it is possible to control a servo using the potentiometer on my tx. It's a tgy i6. My fcb is the CC3D. If it's possible, how would I go about it? Do I connect the servo to the reciever or the flight controller? My reason for wanting to do this is so I can mount my...

Hello! I need help and information with my new potencial build (I'm not sure about it ^^ yet). Would be happy with any kind of data and tips. I want a multirotor that is capable of lifting packages and carry them on great distance and of course needs to be able to return. Also would like GPS...

Hello. I am new here.. I have a question- for the blade inductrix and nano qx, is it possible to perform flips in agility mode using the stock transmitter mlp4dsm? Pls reply ASAP thanks!:)

Hello! I have a question to ask all of you. For the blade inductrix and nano qx, is it possible to perform flips in agility mode using the mlp4dsm stock transmitter? Pls reply ASAP. Thanks !:)

So iv 3D printed a 2 axis servo gimbal for my quadcopter. I have put it all together only to realise one problem. How do you get the servo that controls the roll to have a strong and secure connection to the rest of the gimbal?? For example https://i.ytimg.com/vi/dOu_MZyWr8w/maxresdefault.jpg...

So when I was flying my s500 today with a 4s 5200Mah lipo and 935kv motors I decided to have some fun and go full throttle a few times starting from just a few meters off the ground. All was well except as the quad rockets upwards on full throttle it goes quite a bit off course, as in doesn't...

Hi Community, I have been building my first quad, and when I have gone to test it, it flips on takeoff. I have the below specs: openpilot cc3d 4 x DYS 2830-14 750kv 4 x 14x4.7 props (cw & ccw) Hobbypower simonk 30a esc w/ bec 490mhz Turnigy 30-40c 1000mah 4.s (testing battery) frsky x8r...

Hi Community, I have been building my first quad, and when I have gone to test it, it flips on takeoff. I have the below specs: openpilot cc3d 4 x DYS 2830-14 750kv 4 x 14x4.7 props (cw & ccw) Hobbypower simonk 30a esc w/ bec 490mhz Turnigy 30-40c 1000mah 4.s (testing battery) frsky x8r...

So I bought the eachine ET200 VTX with VC700 TVL CCD CAM and use it with the RC832 VRX. I also have these http://www.banggood.com/Boscam-SKY-FPV-5_8GHz-Petals-Clover-Mushrooms-Antenna-RP-SMA-Male-p-91109.html clover antennae. I'm getting roughly 60m range before my Quanum V2 Goggles go fuzzy...

I don't know how to delete a thread XD

So, i got my 1st bigger quad a few days ago, a Eachine racer 250 to be exact, and somehow managed to burn one of the ESC's while setting it up in Libre pilot. Burned ESC's At 1st i did a firmware update, which reset the whole quad and led to a crash, so i decided to go through the vehicle...

I recently purchased my first quad copter. It came with one 3.7v, 650mAh, H20C LiPO. I have been trying to locate extra LiPOs so that I can fly longer between charges. I have not been able to locate the same battery that came with the quad. I have however been able to find the same battery in...

I was flying my f802 hongtai drone and it got lost behind my neighbors house and I and my brother, dad and bros friends can't find the drone, I last saw it go over the neighbors roof and thats when i was trying to bring it back down, They have a fenced backyard and i can't see it at all. I live...

So, some of you know I have this Flying 3D X8 that Gearbest sent to me with problems. It's looking like I am stuck with this so now I need to figure out what direction to go. I'd rather keep and build something with this if practical, but I will part it out if it makes more sense. The first...

I recently purchased the JJRC H8D quadcopter, this came with it's own radio with a streaming video player for the camera mounted on the quad. The radio has it's own built in buttons for taking photos and videos. After I purchased this, my mentor handed me the Specktrum DX6i radio because he was...

I have a AQ-600 frame and it is the first quad copter I have tried to build so I really don't know exactly what is needed for them so if someone could give me the list everything that is needed and have links then I would really appreciate it!

Hi guys! I was going to bring my qaud on a trip to south africa but decided to just bring a gimbal. I already have the gimbal and motors that I bought from hobbyking. Now I need a 2-axis gimball controller and a thumb joystick in order to controll the pitch and roll manually. I would really...