Search results

Ibus is ibus servos. 3 horizontal pins top right. Ppm is bottom left three vertical pins. Ibus is still ppm. difference between is miniscule unless you race.

Swap to betaflight. That's all I'm saying :cool:

Select serial rx then ibus underneath it in config. Turn ppm on in the tx setup menu. Setup Aux channels with arm & mode switches on them. FAILSAFE Oh by the way on my i6 I could only have ibus if I did the 10 channel firmware. update. Don't know about yours though. Maybe cowboy knows. & lastly...

Oh & the esc wires look like they just had a hair cut from someone who is OCD.:pGetting the use out of that caliper.

No leds normally mean R. I. P. go over the soldering with a magnifier or continuity tester. If BF ain't opening try a different lead different com port different baud rate But if it ain't opening, it ain't opening. So suck it up dig deep & be more careful next time. Just buy the cheapest F4...

Daddy longlegs:D nice. my x220 arms bolt on like that but I put them underneath so I could make the standoffs shorter =:) CG. There is about 6mm of of dead space there. The bolt heads are pretty deep so I filed em down to about 3mm.just enough for a few wires underneath. But this is the shizz...

That's all you can do with simonk esc's is calibrate them in motors tab. Props off. Or do it on a servo tester. Sounds like throttle curve is high or end points are messed up. Try resetting the board as you may have changed something without realising. Even start a new model on the tx to...

This is on the way :) :rolleyes:

The esc in your picture above Jackson is a simonk. That's what I started off with. & not long ago I threw 2 away. Thinking what can I do with two. Well now I know.

I just noticed your using a zop, cowboy. What you think. Mine lasted about 6 cycles before puffed up. Never again.

Esc & motor work on Betaflight. On this setup. No servos on this but makes no difference. running the latest firmwares But i get this message. In mixer tab. I get this on the servo tab. & this is a preset for my model, which ain't working. Aaaaaaaaaahhhhhh. :mad:

I just realised that the turnigy plush is a brushed esc, Doh o_O £9 up the swanny. So just ordered one of these.

Not bothering with quad based fcb's for this wing. I will try the new esc when it comes, but I just ordered the F411 wing FC.

Should work from what I've read. I've just ordered a turnigy plush. Thus is supposed to be made from quad parts. The S800 kit comes with a reptile blheli 2-4S. Gonna try after work & take another working FC out my tweaker.

:(

After 2 days I can only assume its down to the esc. I copied Jackson's barebones setup. Wired the servos direct to channels on the rx & working properly. But the motor is still doing the same. Do blheli esc not work without a flight controller, on a pwm signal. this is all I can think of with...

OK so today I took the servo +- put them on M3 M4 & just the same. Are working. Calibrated another brand new set on a servo tester, then put that on. Only to find the same issue. No motor in the motor tab but if I arm it & apply throttle it will start 3 single quarter turns stop then repeat...

It looks OK or I can't see anything. What is actually happening. Can you still arm it but is the motor is twitching. You don't provide mucho information.

I'm in a spot of bother with this now. All 6 pre checks are lit up good to go. Rx is bound & all good in rx tab. Flashed blheli & happily beeps, so pass through is working. There is a preset in inav for my wing, which I selected. BUT no motor is showing up in motors tab or servos. The servos...

Camera on a pole, good one :p