throttle

  1. GuardianVex

    Quadcopter Unarm or unresponsive after Short Takeoff

    My quadcopter is Eachine QX95 , Reciever is X6B and the transmitter is FS I6 . I am facing a problem ,where when I throttle , the drone make a brief takeoff and then just lands and gets unarmed automatically and I had to arm again and again and again and all I am getting is a short 5-10 cm...
  2. F

    Drone throttles up on its own (real flight not Betaflight)

    Hi Pilots! I'm having a hard time diagnosing the problem with my first self built drone. It seems like the throttle is always going up on its own after a few seconds of flying, I've tired Acro/angle/horizon mode and it does the same thing. I've reflashed the FC too. On the video I cut the motors...
  3. A

    NEWBIE! Need a little throttle help...

    Hey everyone! I'm new to the hobby and just built my first quadcopter a few days ago. While I think I've fixed most of the problems I originally had, there's one problem in particular that I cant get down. Every time I raise the throttle, the quad understands and begins to go up. However, when I...
  4. D

    HobbyWing 80A esc throttle issue

    Hi there, I know it's not strictly quadcopter related, but I built an electric scooter and used a HobbyWing 80A UBEC ESC as the speed controller. I worked wonderfully and didn't even get hot until one day I decided to try out the brake feature on it. They are extremely powerful and stopped my...
  5. J

    ive built my quad but now its too sensitive and has a minuscule sweetspot

    hi everyone i am new to the hobby and i managed to build a full quadcopter by following the very well known $99 dollar quad from uavfutures. ive been try to fix this one issue of my quad being very sensitive even at 10%-15% throttle or less straight after takeoff. this problem i believe is to...
  6. D

    I have a bit of a unique problem

    So I have a Taranis q x7 transmitter with a DYS Omnibus F4 Pro Flight Controller and as far I know everything works on my quad but the weird problem I have is when I put my transmitter in mode 1 I can arm the drone but the roll, pitch, yaw, and throttle are all mixed up. And when I change it to...
  7. tekchip

    Eachine Wizard X220 Min/Max Throttle Problems

    Newb quad pilot, first time poster. Hang on to your butts! I have an Eachine Wizard X220 and a Fkysky FS-I6. This came as a ready to fly package. I've done no configuration or changes to how it came. Everything seemed to link up and work fine out of the box. The trouble comes in trying to...
  8. J

    Trouble arming new build

    Using Flysky's AFHDS 2A protocol with older Flysky FS-i6 and new Flysky X6B i-Bus, PPM, PWM receiver set up for PPM. Receiver bound. The receiver controls are operational under Betaflight 3.0.1. Escs are calibrated. Channel 5 is mapped to AUX 1 for arming. Under Betaflight, I can see switching...
  9. L

    Please help

    I just got a Hubsan h107d fpv quad and the right stick is not self centering but the left one is. All my other quads are opposite of this and it is making it hard to fly and killing my experience with it. Is this a factory issue or something i can fix? Please help
  10. JacobCoy9

    Motors keep throttling up without user input.

    Hello all, I've got a 250 racing quad that's going haywire. It started after I replaced the front frame (I had to de-solder and re-solder the ESCs to get the wires through the frame). When I finished the reassembly, the quad would start increasing power without me telling it to. (See video)...
  11. R

    Throttle max

    Hello, I have a QAV-R with LUX FC and a DX6i transmitter/spektrum satellite receiver. On Cleanflight I calibrated my ESCs with a throttle max at 1850 (and min at 1030) because my DX6i seems to only give a signal from 1020 to 1900 in the receiver tab (with +125% expo). However eveybody seems to...
  12. mozquito1

    Throttle problem

    I was out flying last week when the wind took my quad so I turned my tx off as it looked like it was going towards a few dog walkers. When I got to it a leg had come loose, well the bolt came off. Must have vibrated off and when it landed it ripped the ground wire off the pdb from one of the...
  13. D

    First quadbuild, motors acting strange (videoclip)

    Hi, I´m starting to get finished with my first quad but I do have some problems with my motors to spin the way I want them to. When I push the Arm-button and have throttle at 0 the motors starts to spin even though I have flicked on "MOTOR_STOP" in cleanflight. When I then increase the throttle...
  14. mozquito1

    Throttle problem I think.

    So I bought my first cheap quad to play around with first and got about an hour out of it till I accidentally connected the power connector the wrong way. The connection on the jjrc h8c is cheap and I fried the board. So I thought well if I'm going to break drones I may as well learn how to...
  15. 1

    Quadcopter has too much throttle

    Hello everyone, I've got a 250 size quadcopter here, naze32 rev 6, lumenier 2206 2350kv motors, 5040 props on 4s. When I try to fly it, this little rocket :) does not like to descend. I can't get the throttle low enough. When I reduce the throttle, too low and the motors stop and the quad...
Top