Search results

Don't know if BBC changed there story yet.

Yeeeaaahhh Cowboy. What if he wants or needs bigger esc's in future. I got loads of spares but if I was going to buy any more I'd get 30amp as I'm wanting to try some 2306 soon. 640g per motor on a 1.2kg quad Maybe the chart got lost in translation in Chinese & it wrong. Is that 640g at full...

Servo tester are buttons, £4 on ebay. Save you hours of trouble. I mainly use it to test stuff before use or if going in a draw. If not I can send it back.

You got it, without a servo tester it's a pain but the only way to deduct each one. Jus swap a working motor if that don't work try a working esc it's a pain but you should only have to dismantle 2 arms to get a result. A working & non working, OK maybe a third. But you got the picture.

Do the props actually spin & you just can't get it up? I'd check prop direction again it maybe pushing into the floor. 4 emax 2205 can pull a kg easy. Just one lifts my 600g wing easy. So should your setup. try a higher c rate but I use some 20C compared to 40-75 there is not a major...

20amp Is fine 30 would be safer.

Are you bound to rx & have Aux switches setup eg. Arm & modes. Are endpoints set on both config tab in betaflight & in blheli config on the esc's. Do the inputs work in the rx tab in betaflight. When move sticks do the ranges move.

OK so I'm back with betaflight & have a 90% setup going. All Is configured rx working I managed to get the servos working with sticks in motor tab. Only the servos don't move, only on lipo plug in. They correspond the correct way on motor tab. But I still got my original problem. The esc...

I only use PayPal as they can't see your details & you have payment protection.

Yep that's a drone :oops: It looks like one of them nitrogen ones that go for hour & hours. Basically anything can be weaponised, a dolls pram or even an ice cream.

o_O

I would take the two duds off & test them on there own. Or if not got spares then swap motor ports. If 1&2 don't work then try them on 3&4. If nothing works then try a working motor on a duff esc & if still just keep going through. Just deduct what's not working. I have a servo tester so I can...

Endpoints =1000 low 1500 mid 2000 high Lowest esc value needs to be above the low 1000 orno arm. In the motors tab when you move the slider note what value all motors spin up together. You want this as the lowest esc value. It should be above the 1000 endpoint for low point. Note lowpoint & esc...

Yes one wire per channel, 4 for sticks & 2 Aux channels for arm & modes. Get the firmware cable & you can get to use all switches with the 10 channel update. But you will nerd the ia6b Ia6c, X6b to use ibus/ppm. Also the Aux channels have to be setup before any input shows in the rx tab in...

From what I saw was just an explosion. Nothing hovering. Local news say there was a fire & cannister went off. People probably are using drones to find out what he doing & he using it.

Even on th British Bullshitting Corporate News they're saying it wasn't a drone. Apparently it was a gas cannister. & he paranoid of drones. Because he's up to no good.

Just get the cheapest Windows 8 tower you can off ebay.

I just googled it & they dropped XP & vista. I bought my tower from ebay for £30 as it was only for betaflight. Bargain. Graphics card is a potato but it works.

I thought I was bad on windows 8.1. Should work as long as it's 32bit or more.

For me the chrome app hasn't worked for a few months now. Download blheli config while there if not got it.