Search results

My mistake I was using the ts832, the massive chunk of a vtx when I go the breakup at 200' Lucky man my battery has no USB port, I'll find a charger that works for mine. I now have the ts801 so poop maybe I just need to sack up and see how far my bird goesbefore I get the breakup. So...

Hey yeah I saw you and I are both having motor noise issues from my other post. Sense I've fixed the quad with the seperate plastic mount for my rp-sma i haven't tried them again. The battery pack is dead and I don't have a charger for their battery. Kinda nerve racking sending my quad up...

Allllrighty then, guys I've upgraded my Goggle's to spectrum focal v2's (fatshatk attitude V3) Gear: My vtx is the eachine tx801. Running at 600mw (proven with my ev800 goggles the range is about 1000') Now the diversity module just says Fatshark FSV2445 V2 Symptom: The image is clear but...

I never found a decent way to achieve true division between conductive parts and the carbon. I tried eletric tape heat shrink nail polish and plumbing tape. I ended up using a piece of plastic bolted in on the top. Perfect flex and it houses the 90 rpsma. Crystal clear image now. Now I can...

PROBLEM: Ok this was a weird one to figure out, but long story short the pigtail rpsma 90degree fitting was conducting on the carbonfiber giving it motor "noise". MY FIX: I used nail polish like 3x coats on the screw holes and pigtail hole then added extra electrical tape spacers so there would...

I do have a capacitor with the battery pigtail, when I get back into the quad I'll check for any fractures in the soldiering. It's a board with only 10v pads by the vtx and camera plugs. So I'd have to splice in the power because the clips are not able to solder. Its getting much worse. I...

Alrighty hey guys I'm back again with another question!! Quad: tryro99 Goggles:spectrum focal V2 Vtx: eachine 600mw I am getting a crystal clear vtx signal when I plug the battery in and power up the quad. Once the ESC beeps are done I still have a clear image, but once I arm I get lots of...

So in my early days of drone flying I wanted to go budget and ordered two 1500mah 45c 4s lipos from Floureon for 29$. I have been using them along with my tattu 1500mah 75c 4s lipos and I don't notice a difference. Same flight time same punch power. Am I just over working my 45c batteries...

OoooooooooooooooooooooooOoooooooooooooooooooooooOooooooooooooooooooooooohhhhhhhhhhhhh! ... It works. Thanks Renov8r moquito1 and the rest! You have made me so happy. Like seriously thanks!!!! No more Sim!

Well then I would say that's the problemo!!! Let me give it a try and see if it connects. Might be a few days because I'm not around any solder gear. Thanks again for the help I'll report back soon!!

Ok so I think I am getting somewhere. The wires connecting fc to rx areaattached with a plastic clip on the fc side. Next to the clip housing on the fc there are 3 small copper pads in a row and labelled beside is: Ppm DSM [OOO] IBUS (^Pads) On the fc right next to...

I found that right after my last post. I followed the steps and still no PIDs on the recivet tab. I'm on bf and can follow along untill he gets output on the sticks. My friend let me borrow his tx same version as mine and it does the same thing so I'm guessing it's not a broken tx. Here are my...

Good sounds familiar ive tried with those steps in the past but I'll try again. The hard part is understanding which UART to turn the serial Rx on. Do I need to plug the Rx fc cable into another slot on my RX or is channel 1/ppm still ok? There is are only two ibus Slots at the top labelled...

Ok I want to do that sounds much better. What would be the checkpoints in setting up ibus just the configure tab selector and correct slot on Rx?

Tx is flysky fs-i6 with no 10 channel update. Rx is the flyksy fs-IA6B The PPM output is on on my tx menu. I have the fc plugged into my RX Through the ppm/ch1 slot. Binding the Rx and Tx is successful and I can see the Rx with the battery life on the display. Now for betaflight. On the...

So I'm really starting to get into drones and I own 3 now but one tranmitter. Flysky i6 I just bought the tyro99 and after finishing the build I can't get the controller to show any pid's in betaflight after I bind it. Has anyone had success binding up a FlySky through PPM to the tyro99 ? I'm...

Alright I think that might have been the issue, I always tried to throttle up after I crash to see if I can right it's self or take off from after crash. I will be on point with my disarm switch now!!!! Damn even 2 "sets" a year would be good for me! Once I get my new parts I'll let your guys...

Cool, I've got my mind set on an 4 in 1. So I guess I just have one more real question to ask which is about "32bit" So if I get a new fc tower that can run 32bit and esc's to match. The 32bit rating is referring to what? From what I understand it means the fc and esc's can compute larger...

Dugdog47 I'll have to check out that 4io on banggood but I'm on a budget so hope it's not too pricy!! Renov8r Super helpful advide, thank you. Sense I've bought the battery's I haven't really been able to fly so I haven't tested them. The ones I flew with previous were 75c 1550, my props...

My motors are eachine 2300kv, MN2205. I do understand about how not to hold full throttle for too long or they'll fry. I have tuned my pids to around 700d/s with less expo. Matek f3 Flight controler and pdb My props are cyclone t5045c The majority of my esc deaths happen when I'm flying in...