Any help appreciated

M

Mark Blake

Member
Im having trouble wiring a Naze 32 flight controller to a new FRsky x6r receiver. first time using cleanflight as well, i wish there was someone in my area that could help. I live in northern VT.
 
mozquito1

mozquito1

Well-Known Member
Also change receiver type in configuration tab. & turn serial rx on
On which ever uart you use on the ports tab.
 
M

Mark Blake

Member
when cleanflight recognizes the receiver the channels are all wrong, the throttle is on the right? there isnt even a mode that puts it there. another flight control;ler does the sane thing, and another radio and receiver do as well, im freaking lost on this. not in any you tube video instruction have i seen this one.
 
M

Mark Blake

Member
serial receiver on, telemetry on, s-bus selected, everything recognizes, but it still has all the channels twisted around.
 
mozquito1

mozquito1

Well-Known Member
In CF, I think it's on setup or receiver tab up top. It says AETR1234. click it to change the stick layout.
 
mozquito1

mozquito1

Well-Known Member
If that doesn't work try a board reset & set it up again. Don't reload any backup.
Naze where all the rage @ one point. I went through 7 in my first year.
Glad to see the back of em.
 
mozquito1

mozquito1

Well-Known Member
If I remember right with the naze32, you can't use a uart while the USB is in use.
I can't remember which though.
 
M

Mark Blake

Member
found a video that laid out the same thing. worked as advertised. sticks all set everything set for flight. set new channels in the radio and receiver, they don't show on Cleanflight. watched 2 different videos on how to set switches on the x9e. set 4 switches, re-bound the receiver. nothing works in Cleanflight as shown on you tube. any suggestions?
 
M

Mark Blake

Member
Your help on channel programming was spot on. Can't thank you enough! I have set 4 channels up on the transmitter, as per tarannis videos, re-bound the transmitter to the receiver, but the extra channels don't show on cleanflight like they do on the instructional video? any suggestions?
 
M

Mark Blake

Member
Mark Blake said:
Your help on channel programming was spot on. Can't thank you enough! I have set 4 channels up on the transmitter, as per tarannis videos, re-bound the transmitter to the receiver, but the extra channels don't show on Cleanflight like they do on the instructional video? any suggestions?
Click to expand...
all show on the transmitter, all show movement in the model secton, but none show up under receiver in Cleanflight.
 
mozquito1

mozquito1

Well-Known Member
Where you set modes up in the tab do the switches change the ranges.
eg Arm switch
If it they do. I would try to fly it.
It may just be a glitch. Maybe try deleting the flight program & reload it.
I used cleanflight for 3yrs & when the standalone betaflight came out I deleted both chrome apps only to find the cleanflight SA wasn't a full file to run it.
& I could not re download it so I I'm on Betaflight now. And don't even know if the cleanflight crew sorted it out.
I got 2 quads with OSD & 2 without.
Does CF have osd tab these days.
 
mozquito1

mozquito1

Well-Known Member
Board reset, swap to an earlier update. Try reload cleanflight if not download the standalone Betaflight off github.
Check the board for small splashes of solder. If any of these don't work then it has to be a fault on the board.
I found a few of the naze to have dodgy motor pins as the board was working but pin 3 signal or ground was bust some how as all 4 motors & esc's worked on the other 3 sets. Other boards just stopped kuput. Lit up but picking nothing up & no USB.
 
You must log in or register to reply here.
Top