Search results

  1. BL Swagger

    What omnibus F4?

    I feel your pain. Everything I get off Banggood comes naked. No directions or papers of any kind for my FCs or other components.
  2. BL Swagger

    FlySky FS-i6 wont work after CleanFlight firmware update

    I have a 4in1 20a esc so the ground and power connect directly to the PDB. After I reset the flight controller (new firmware, everything), I put the props on like you suggested and it flipped over. But then I remembered I'm prone to putting the props on upside down... so I dbl checked and...
  3. BL Swagger

    FlySky FS-i6 wont work after CleanFlight firmware update

    Update: It lifts off! The balance is terrible but glad to see I have working components... I think lol
  4. BL Swagger

    FlySky FS-i6 wont work after CleanFlight firmware update

    The quad flipped when I had props on. I think I may have damaged the 1 & 4 pins on the FC that connect to the ESCs. The soldering was a bit sloppy, and this FC has been rewired a few times.
  5. BL Swagger

    quadcopterframe.com (everything marked down)

    Just bought a frame. Very nice site too btw.
  6. BL Swagger

    Gearbest clearance sales! Up to 70%!

    Did some of these deals expire?
  7. BL Swagger

    FlySky FS-i6 wont work after CleanFlight firmware update

    To avoid posting a new thread, I am going to attempt to continue on this thread considering it is the same build and a similar issue. First video shows the control of the motors using the Master Control on CleanFlight. The motors rev up in sync. The second video shows the control of the...
  8. BL Swagger

    FlySky FS-i6 wont work after CleanFlight firmware update

    After ESC calibration, the quad seems to be working great. Thanks guys! Now on to the VTX
  9. BL Swagger

    FlySky FS-i6 wont work after CleanFlight firmware update

    Ahhhhh... very true. I assumed because it worked well on initial set up that I wouldn't have to do that. That could explain the weird response I was getting before. I'll start over, and remember the ESC this time.
  10. BL Swagger

    Betaflight Stand Alone.

    You forgot about Microsoft Edge..
  11. BL Swagger

    FlySky FS-i6 wont work after CleanFlight firmware update

    Yes, I received this FS-IA6 receiver. And the PWM is the correct mode. I know that now. But I am having issues getting all the motors on the same track, and sometimes arming the quad is not working. I am trying out new firmware at this point. If the quad does arm, then the motors don't respond...
  12. BL Swagger

    FlySky FS-i6 wont work after CleanFlight firmware update

    Update: Not sure if I fixed the issue. I thought the FS-i6 would use a PPM receiver mode. I was not getting a response from that. I changed it to PWM (one-wire per channel) and now it will arm and give me readings on Betaflight. (correction from before, I am using betaflight). However, only 3...
  13. BL Swagger

    FlySky FS-i6 wont work after CleanFlight firmware update

    I had quite the ordeal figuring out how to update the firmware of my SPF3 FC . Turns out the issue was a faulty mini USB cable the whole time. Before updating the firmware, my quad would arm and run just fine. I needed to calibrate everything using CleanFlight, which resulted in updating the...
  14. BL Swagger

    DIY Quadcopter, RC Config

    Thanks, I have learned a lot since first posting this. I needed the reassurance on the transmitter. I also like the transmitter better that you recommended, Jackon.
  15. BL Swagger

    DIY Quadcopter, RC Config

    I have decided to do a DIY Quadcopter. I will be purchasing a starter kit to jump start the project since this is my first DIY. I have some questions concerning the RC transmitter/receiver though. I have made the questions bold. The starter kit comes with: 1) Carbon Fiber Frame 2) CC3D Flight...
Top