Search results

  1. mozquito1

    Bugs 3 and a Flysky Transmitter

    The only potential for mods is the frame by gutting it when or if the board fails & putting in a new FC & esc's, rx & you maybe able to push them motors to take a 3S lipo. Just fly it like you stole it. £10 FC £30 for esc's Yo already got tx/rx so 40 rips you will be good to go again. Acro or not.
  2. mozquito1

    Motors cutout

    Tham sockets these days I just heat them & pull em off, then just brush it with the iron & the pins come off. Then just direct solder the wires to the board. It looksike a pin is missing on purpose but it may have snapped off the other may have just been slightly off but bent & still just...
  3. mozquito1

    Motors cutout

    You got a few options just be careful not to short anything. Keep us updated.
  4. mozquito1

    Where do FPV goggles get their data from

    Probably because it has a screen and video out socket.
  5. mozquito1

    Motors cutout

    They don't have to be the same colour, Just label them or write down what corresponds as.
  6. mozquito1

    Motors cutout

    Or nail varnish.:D
  7. mozquito1

    Motors cutout

    You could carefully cut that down to 3 or just put 3 bare end on then hot glue them.
  8. mozquito1

    Motors cutout

    I used to practise on an old TV or hi-fi I had with small pins on it. They might even have what you need. It may just be a case of joining 3 wires. Or has anyone near you got any old electronics. TV, hifi, they normally use these parts.
  9. mozquito1

    Motors cutout

    Can you solder or do yo own a soldering iron. I buy a reel of each colour. Red black yellow & green silicone coated 30awg & heat shrink. You could carefully take the socket off & direct Solder to it. Sounds like the plastic has weatherd & shrunk or something. I think they are 3pin male micro...
  10. mozquito1

    SNAPPER7 WATER CRASH DURING SPEED RUN

    Santa likes milk :( Was it waterproofed. Liquid silicone or nail varnish.
  11. mozquito1

    New Build is it worth it????

    I wonder what voice command puts it into recovery modeo_O lol. When your in that moment & you say the wrong one leads to another until your just swearing at the tx:mad: 2k :eek: that's worth more than my car:oops:
  12. mozquito1

    Is this OK/Safe to do with LiPo batteries?

    What size as anything over about 2200mah is going to slow it drastically as opposed to say 1300 - 1500. It will be sluggish & make acro flying hard unless you adjust the pids to account for it. But yes its safe. Just check the cells after flying & balance them before next flight.
  13. mozquito1

    Drone fell into lake.

    Get yourself a fishing rod or scube gear. You just give me a flashback. Horrible isn't it. At least davey Jones is having fun. Even after 4 years I stay away from H2° unless it's clouds. At around what distance did it happen. If it's 1' outside manufacturers stated usage then it will probably...
  14. mozquito1

    Flight Controller Software

    Tx - rx - fcb - esc's - motor, is the chain of command. I'm no boffin but tx-rx has no input to the esc's, so that makes no difference. Its fcb - esc & it's not the refresh rate that matters, it's the ESC response rate driving motor speed changes that makes the difference. All I know is ppl use...
  15. mozquito1

    Motors cutout

    Voltage sag or not much flight time is what I'd think from an old battery. Sounds like the rx, maybe dropout then it's catching it. Reflow all the solder joints especially on the receiver & lipo pigtail then Try it again. Definitely worth doing the latest betaflight config RENOV8R mentioned...
  16. mozquito1

    Bugs 3 and a Flysky Transmitter

    Just take out the tx & put the stock flysky rx in it. Did you get the ia6 pwm or an ia6b with the i6 tx. What rx is in that bugs. Just had a quick look at it. I wouldn't bother just use it as a trainer until it breaks. It's guts are probably all on the same board. Fcb, esc's, rx. With some...
  17. mozquito1

    Where do FPV goggles get their data from

    H906a will just tune into any 5.8ghz vtx. Range depends on the antennas supplied. Rubber duckers being the worst Omni the best in my opinion but mid range. Helicals get the longest range but require head placement. If you got a tracking system then you can't get any better. Combine the TBS...
  18. mozquito1

    $120 450 build

    I tested mine before I put fpv gear on a build. I was at the beach & made a circle in the sand, put the quad in it. Then walked the next mile marker & give it a qtr throttle & some forward & throttle down. Walked back. It had moved abt 15'. I then faced it towards where I'd be at 2mile but I...
  19. mozquito1

    $120 450 build

    Dji = spoil the fun. I'd have to mod it like steel did. Rip it's guts out:mad:
  20. mozquito1

    $120 450 build

    x6b receiver gets about a 500 meter range. Have you tested that to the max? did you get drop out. I've had over a mile off all FS rx's except the A8S, ppl on YT had 2.5Miles with no mods Off the stock setup. Advertised as 300m park flyer, same as x6b. I wanted to fly like bexamous on YT But...
Top