Search results

Bottom right yellow pins is uart1 So plug in the servo plug on rx then if you have a double ended servo plug into uart1

Still on uart1 then, but in betaflight still try serial rx in ports tab then apply ibus in the rx menu in the config tab. Try both configurations on each ppm & sbus pin on the ia6c pins. It will definitely work on ppm but sbus/ibus is a faster signal giving better response.

I see someone is using a T9X with that T6a rx so it's ppm aswell as pwm. The transmitter is programmable with a pc So just 3 wires needed 5v from rx channel 1 to 5v on uart1 pins Ground on channel 1 to G on uart1 pins Signal on channel 1 to rx on rx on uart1. When wiring signal pins tx is...

Sorry I got mixed up I thought you had a turnigy evo. The cheap hobbyking & turnigy 6ch Have no menu's so I'll check if they are pwm or ppm, they still go on uart1.

Uart1 still, sbus is ibus on that rx. Just try it. If not just turn off serial rx in ports and then change to rx ppm in receiver menu in the config tab. Change tx menu back to ppm. Tx should now work on ppm on uart1.

With a bit of fishing & another £$10 you could get a flysky-turnigy i6. & programmable tx. But out of them 2 posted it would be the turnigy.

@miky94 top right of the pic it says uart1. On them pins. 5v-G-signal rx. I own a turnigy evo & it's a good tx. Ia6c rx on uart1. I never used a wii but its got to be better than a naze. Ibus is serial rx in receiver menu. Then in the evo menu turn on ibus. Ports menu on Betaflight apply...

Stay away from anything naze. Believe me, don't waste your money. For literally a few dollars or quid more get an F4 omnibus. Race flight. Kiss,lumenier. Naze are brittle & break easy. I got an old SPRF3 that's been working fine for 3 years now. Atleast get one of those.

Superglue level:D That must take some patience, I'll start with bricks.

@roger jones are you still doing the rock thing. I got out for an hour yesterday morning and when my Lipo's had ran out I checked some posts out and remembered what you said a while ago. It ain't easy brother, not with pebbles anyway.

Where ? I'll roger any bird me :D

Do you mean format the flight control. If this has happened after the flip then it looks like the board is damaged, If its not picking channels up. Where the values OK before you tried it. eg min 1000 mid 1500. All the answers are above anyway. Good luck.

Sorry no battery left & it's 3:20 am Im up in 5hrs.

You could try the transmitter menu to see if ppm is turned off on rx setup. But Aux is working so shouldn't really be that. Was the tx rx bound when you got it.

So they are there but not working. You didn't say that. Then it's back to AETR1234 Config tab, receiver type set to RX pwm Save it. Disconnect then connect & check it saved as rx pwm. Then goto receiver tab & check it says AETR At the top. Like this or jut AETR. This is the setup for...

He said in his 1st post the calibration did not fix the values. It wouldn't. That is for esc's. The board reset MAY fix this. My build was A OK but it fixed my problem, whatever it was. Just one of them things. If it flipped it was all there. Except props on wrong way Or ESC's on wrong motor...

All the above is all I got for this problem. 3 for the flip & a board reset 3 for the rx problem & Individually check each rx channel on the pin that is picking something up on the fcb.

Reset the board See if all the channels show up again. The only other thing to cancel a bad rx is to plug each individual channel into the pin that is working on the flight controller. The one that is picking up the Aux channel. Get me? If it picks up each channel in turn then it's the flight...

I just checked what you think I said "format tx" I did not my friend. If I did please quote it. I said reset the board in settings tab Second one down reset settings.

In the setting tab next to the calibrate accelerometer is the reset board. It knock everything back to stock settings. I had the same problem flipping & after nearly 2 weeks going over everything. Checking all thing I said above. It was RENOV8R who said try a board reset, so I tried it &...