syma x5c problem

liviu

liviu

New Member
i started and played with the drone, after battery was empty, i recharged it and when i put the battery back in it flashes the LED's and it doesen't si.cronize with the remote. what can i do?
 
make sure when syncronizing that both handset and quad are off . turn on quad then handset then bind together
this should work and allso when useing video make sure you turn camara off before quad or you get corrupted files
phil.
 
Okay, I have a Syma X5C, and the exact procedure I go through each time (which works every time) is this: 1-With the drone and the remote off, turn the remote on. 2-Now turn the drone on (you should notice that the LED lights on the quadcopter are rapidly flashing). 3-Wait for the LED lights to start flashing slowly. 4-Now, take the throttle stick on the controller and push it all the way up and immediately back down (this binds the controller to the drone).

Hope this helped. ;)
 
phil stokes said:
make sure when syncronizing that both handset and quad are off . turn on quad then handset then bind together
this should work and allso when useing video make sure you turn camara off before quad or you get corrupted files
phil.
Click to expand...
As you said with the toys, quad on first then transmitter with throttle DOWN. To bind push throttle UP then DOWN again. Should be good to go now.
 
Also note that if they are very close they will not sync, set the receiver down a few feet away
 
Jackson's got it right. Quad on first....wait for drone lights to go from fast blink to slow blink....then TX on....Throttle all the way up then down....you're ready to fly.
 
I turn the transmitter on then the copter. Wait for the lights on the copter to blink slowly then push the throttle all the way forward, listen for the beep then pull the throttle all the way back and listen for another beep. Observe that the lights on the copter a steady (not blinking) and I'm ready to fly. Always works for me.
 
liviu said:
i started and played with the drone, after battery was empty, i recharged it and when i put the battery back in it flashes the LED's and it doesen't si.cronize with the remote. what can i do?
Click to expand...
I'm gonna go with DJI dude and Jimbir on this one. I double checked the manual and it very clearly instructs you to turn the Tx on first then turn on the quad. Push the throttle full up and then full down. There should be one clear sound from the Tx. Actually. Tx first then plug in the battery is true for every other quad I own.
Now having said that. Watch this video and the guy powers up the quad by turning the quad on first and then the Tx. So Phil Stokes, Jackson and Patton are also right. What to do. What to do.......
I just got a X5C1 UPS this evening and have not even had a chance to open it yet. You can bet that I am going to try binding it both ways after I charge the battery. Interesting.
The binding is around 3:25 on the video by the way.
Pretty unique. Looks like we're all correct.o_O
 
Im getting one next..but a BNF with no camera for $18.00 and Tx $12.00..a few dollars to do the "good" antenna mod...I plan to just use an 808 #16 camera
 
I was finally able to get my X5C1 charged up today ( family stuff kept interfering). I had to fly inside because of weather. What a great little quad!! Anyway. I can bind mine either by turning the Tx on first and then the quad or the quad first and then the Tx. Everyone is right! Sure is a flexible little rascal. Can't imagine liviu had a problem. Are you flying again liviu?
 
Ok, this is my first drone... and Ive done everything that the book has said, and everyone here has said, but all I get is the consistent rapid flashing of the lights. It never slows down!!! What to do? The 'bars" like on your cellphone consistently flash as well on the handset as well... Ideas?
 
You must log in or register to reply here.
Back
Top