dji naza lite newbie help ???

N

niko

Member
hello i'm from Belgium and i just bought a dji 450 frame with naza lite and gps
but no transmitter and reciever whas included
but meanwile i orderd the tgy 9x wit 8channel reciever
so i tried too connect it with my computer win 10 does not work
win 7 64 bit i tried to install the driver then the assistand from naza lite
it just won't make connection and i cant find it too rederict my driver with naza can annyone pls help

thx already
 
ringolong

ringolong

Well-Known Member
I use both a mac and a 64bit win7 machine without issue. Did your kit come with the DJI usb cable?(not all cables are the same) My cable has the work DJI on it. Have you tried other cables if not?
 
N

niko

Member
ringolong said:
I use both a mac and a 64bit win7 machine without issue. Did your kit come with the DJI usb cable?(not all cables are the same) My cable has the work DJI on it. Have you tried other cables if not?
Click to expand...



thx for reply @ringolong
i don't no is it really important that the tx receiver is connected properly i'm using a tgy 9x 8ch receiver band new from the box and to anser your question i did'n come with a dji cable
but win 7 does see it but it says this is a unidentified usb device code 43 it gives
but i tried even on a mac from my brother and there it is the same so it must be something that i do
could you send a link from the right receiver connection greetings
 
ringolong

ringolong

Well-Known Member
Do you know someone you could borrow a cable from to test to see if that is what it is.
http://www.ebay.com/itm/DJI-Naza-Li...168993?hash=item4199615ca1:g:tuQAAOSwLVZVoCVA

I am not familiar with your radio, but is should map like this if you are using mode 2.

80200-Transmitter.png
 
N

niko

Member
Hello first of all thx for the tip I use my car GPS cable and viola all the stress for nothing so thx allot so I have connection the program works I tried to setup my reciever via YouTube and most thing work only I cannot calibrate my controller well I,m really a newbie in rc quads my search Will go on
Greetings
 
ringolong

ringolong

Well-Known Member
It is located on this screen. I would recommend researching updating the firmware on your controller to V2. Huge improvement over the stock firmware.

Screen Shot 2015-11-15 at 1.01.55 PM.png
 
holtneil

holtneil

Well-Known Member
Moderator
Hi mate bind the transmitter to the receiver first then wire up to the Naza lite , plug in USB and power up transmitter then the quad it should then connect to the Naza assist this should then install driver needed and your be up and running
 
N

niko

Member
Goodnight I installed the update I calibrate the controller and reciever also the imu I calibrate so maby tomorrow when the weather let me fly. I can try grts
 
N

niko

Member
Hello guys just keeping you updated in my maiden flight I must say it fly,s really good and super stable next time I will try bigger props now I fly with 8.45 props and I've got still 10.45 props but it was also with a gimbal on... And I tried the GPS and it work so I want to make a picture and I put the controller on the ground I make 5 pictures and the I want to take control again and the controller battery are empty haha so it just hovers there lucky on GPS mode... pfff haha really strange ok see you later here cheers
 
Dudeskin

Dudeskin

Well-Known Member
make sure you set up your failsafe properly, and always check your battery before flying, you dont want it to fly away! i recommend upgrading the lite to the v2, cant be done online and it made my hover even better.

edit, i should read the thread sorry.
 
You must log in or register to reply here.
Top