Connect FS-IA6B to Racerstar StarF3S with SBus or IBus

DriftTurtle28

DriftTurtle28

New Member
Hi Guys, this is my 2nd racing quad I build, because I lost my first one in a neighboorhood.
For my first one I had a FC, a PDB and used PPM to connect to the receiver.

This time I went for a all in one board, with 4x esc, FC, and PDB, only problem what I'm facing right now is, this board doesn't has PPM to connect to the receiver, but uses S or Ibus.
Receiver is already bind to the transmitter, but I can not get my input in cleanflight.
When I move my sticks, cleanflight doesn't move anything.

In the attachments I have added 2 pictures, that's how I wired the Racerstar to the receiver;
Receiver > Racerstar
G to GND
V+ to 5V
S to SID

Made a little video to show you, link is down below:

Thats how I wired it, hope this is clear.

my parts:
Racerstar StarF3S 30A BL_S 4 In 1 ESC 5 V BEC w/F3
FS-IA6B Receiver
Emax 2600kv Motors
FS-I6 Transmitter
 

Attachments

  • scheme 2.jpg
    scheme 2.jpg
    46.5 KB · Views: 3
  • scheme.jpeg
    scheme.jpeg
    84.8 KB · Views: 3
So you can put an ia6b on sbus pins on fcb & that i6x works ? So will any sbus rx work then ? Frsky.
Or still only FS equipment.
Stuff is getting alot smaller in this hobby.
I just received a new, well new to me
FS-RX2A Pro. It's stamp size with more range supposedly than all the others they have. I may swap the Unify nano from my stingy frame with this GEP rx.
As they both the same size & not even 3 grams between them.
I didn't realise the tramp hv I bought was the euro version. Although it said
0-600mw its only 25mw. False advertisement. Lesson learned.
But it does get me around my spot with ease & without static. See how far this GEP gets me on range.
 
mozquito1 said:
I didn't realise the tramp hv I bought was the euro version. Although it said
0-600mw its only 25mw. False advertisement
Click to expand...
In the UK FPV frequencies that can actually be used legally is limited, 2.4ghz 10mw and 5.8ghz 25mw. Many official companies will not want to get slammed for selling illegal stuff.

BTW they sell 3 versions.
* The EU Version is identical to the International, and USA versions, with one exception. The firmware is region-locked to prevent transmission outside of the EU ISM band. All ImmersionRC/FatShark channels are still available, along with 6 of the 8 RaceBand channels. Power output is limited to 25mW also to meet EU RTT&E Regulations.
Click to expand...
 
Lots of UK sellers selling things they shouldn't be. I'm legal in my park & not when I'm not. No one is selling the race wand. & not that many about to unlock it. :(
 
Last edited:
:rolleyes: ... ( A bit of thread jumping here) ... Hey Moz, did you get that capacitor question sorted on the
small frame that a 1000 mfd low ESR cap was too big for ? ... I saw the thread, but couldn't reply at the time
and now have lost where it was! o_O
 
Gyro Doctor said:
:rolleyes: ... ( A bit of thread jumping here) ... Hey Moz, did you get that capacitor question sorted on the
small frame that a 1000 mfd low ESR cap was too big for ? ... I saw the thread, but couldn't reply at the time
and now have lost where it was! o_O
Click to expand...
Not much difference in size of a 25v to a 36v, so I opted for a 16v 470uf.
It's about 1cm long by 1cm wide.
See how it goes.
 
Jackson said:
Looking at your pic, I see this connection on your FC.

View attachment 4125

Did you watch the vid?​
Click to expand...
Oh, I watched again, so the only mistake I made was the white wire, it should be soldered to a Rx point, I will add a picture to where I'm gonna solder it:
sYWSyyr.jpg
 
You must log in or register to reply here.
Back
Top