Search results

Yes, what HDtallrider said, the gears are needed to get high enough torque to get off the ground. You could remove the top of the shell and hotglue/fasten some of the parts that loose their supports.

Aw should have looked in the mirror.

Yes, before you buy these you may want to see if @holtneil agrees. He is far more experienced on the hobby side of electronics than I am.

The spektruim radio is really going to climb before the sale ends. If you can get it, then go for it. The FlySky transmitter would make me sceptical. I'd even get a HKTR6A before trying what appears to be a knockoff. A orange Tx is around 40 pounds. The FPV system looks nice, the 32ch...

22.31 top 24.99 bottom I really recommend mutistar, as they are specifically designed for quads. Here is a muti-star racing battery. I highlighted in blue important specs. Where it says 3S1P, it is referring to the battery layout. 3 Series (add voltage, same capacity), 1 set Parallel (add...

Haha, you can use a PS3 controller over bluetooth, but they don't have anywhere near the range. They of course can be modded if you like the feel of the controller i your hand.

I was supprized to see a single sided PCB. You could make one of these if you could get a transmitter module and a couple of compatible joysticks.

Haha, I googled this for a little before I was satisfied. Aslo make a note that if you plug power into the side or the HK's Tx using the 9mm power jack, it will not transmit. You need to have batteries in it. This greatly annoyed me so I modded mine to accept batteries. You can use the jack...

I like to connect mine in an L shape. You only need 1 ground and one power from the KK, because all of them are bussed(connected) together. You can take the signal wire down further than three of course.

I am not familiar with the naze, but I think all full FCs have it. Here are the settings as I understand them on the KK2.1.5, this may be true for the Naze. Pgain - how fast the quad responds to re level Plimit - ~5 controls how much you can make quad go from level ACC trimming positive -...

Power comes over the red (usualy) wire (depends on your cables) from the KK2.1.5 board. The pins are as follows: outer edge: - Middle: 5v+ Inside: Signal(data)

here are a couple: http://www.hobbyking.com/hobbyking/store/__58318__Turnigy_B6_PRO_50W_6A_Balance_Charger_White_.html http://www.hobbyking.com/hobbyking/store/__5548__IMAX_B6_50W_5A_Charger_Discharger_1_6_Cells_GENUINE_.html

Ok, sounds like you are having trouble arming it. Hold your left down and right. THis arms you. To disarm hold the left stick left. To enable auto level (Stick mode) Hold the right stick right while either arming or disarming.

Depending what you want your charger to do. If your just starting out you can grab $15 one from Hk, or you can get nicer ones over $100. I have this one, it feels really solid and works great. It does not have the abilities to discharge batteries to store voltage or anything like that, but I...

Welcome to quadcopter forums :) To rule out the transmitter could you verify it on your other quad? It sounds like ESC or FC problem could you test this, or post a video? Sometimes you could have it set to re-level too fast.

@holtneil Haha, it is easy to get a little OT. @Lukaskk To get all of the information compiled could you edit your main post to show your current part list, it makes it less confusing if you ask a question.

Do you just lightly sand the solder mask off then tin it?

Makes sense.

Are they mystery brand, xD. By mystery ESCs I thought they meant they don't know what they are. :p Why have the KK2.x.x and a Mini line to sell? The mini just looks like a condensed KK2.1.0 board.

Also HoltNeil, what is your opinion of the KK mini supposed to have all of the same functions as the full KK. It was made for minis and micros.