My latest build

Herpderpwerp

Herpderpwerp

Well-Known Member
This is my latest buld quad, it still using parts from my first build :

Suppo bl-2814/6 1400kv motors
50A opto esc also from suppo
10mm x 10mm aluminium for the arm and landing skid
Custom lasercut mdf body (planning to change it with something lighter in the future)
5400mah 45c battery (planning to add another one to pararel it)
Cc3d FC (planning to upgrade it to cc3d revo)

Total airweight is about 2500grams with camera and gimbal attached.

Total thrust is about 8000 grams with 10x6 props

P_20150808_114814.jpg P_20150808_121248.jpg

It is a wide x form frame
 
Are those 46 gram ESCs made for multirotors?

Think I would have gone with some multirotor ready SimonKs.
http://www.ebay.com/sch/i.html?_odk...simonk.TRS2&_nkw=50A+opto+esc+simonk&_sacat=0

Tried to find some specs on your motors, found this.
2814-6 1400KV Outrunner Brushless Motor for Quadcopter Multicopter 4-Pack

Specifications:
- 100% Brand new and high quality
- Rpm/V : 1400KV
- Weight :117g
- Motor Dimensions :28.6mm x 14.5mm
- Shaft Size:3.0mm
- Battery Opernating :2-3 Lipo
- Current :0.3A
- Peak.Amps :14-22 A
Click to expand...

Going with these DYS 40A you could save a whopping 104 grams.
http://www.ebay.com/itm/DYS-40A-Sim...Multicopter-/271945974671?hash=item3f513e438f

Oh well, just saying. :)
 
Hahaha, actualy the store where i bought the motors end escs are specialized for plane and helis. And that time i didn't really understand the differences between the escs or motors, But when i set up the esc with the cc3d GCS, it automaticly set the frequency to 490hz, and i can't find anything wrong when i try to flew the quad. It responded nicely with the stick input.
The only complain was the flight time, only 5 minutes LOL.
Planning to pararel the battery to 3s2p or 3s3p and using balsa for parts of the body to lighten it
 
I really like the design, also if you have problems with stabilizations try flying without auto-level and just stabilization. If that fixes it then your FCB is getting too much vibration.
 
Jackson said:
2k/motor? Sounds a little high.
Click to expand...
Suppo bl-2814/6 1400kv motors
50A opto esc also from suppo

If those motors are even able to handle 40 amps then that much thrust can be expected. I agreed until I saw the big ESCs


I believe that the 6 pitch props may be a little big, check to see if anything is getting hot if so switch to 9x6 props and if your going to be using plane props I suggest you move to lightweight wood props, they are stiff, cheap, and better balanced than CF props.
 
GJH105775 said:
Suppo bl-2814/6 1400kv motors
50A opto esc also from suppo

If those motors are even able to handle 40 amps then that much thrust can be expected. I agreed until I saw the big ESCs


I believe that the 6 pitch props may be a little big, check to see if anything is getting hot if so switch to 9x6 props and if your going to be using plane props I suggest you move to lightweight wood props, they are stiff, cheap, and better balanced than CF props.
Click to expand...
The one that getting hot are the cables, the one that attached to the battery and the xt60 connector. I think the amps draw are a bit high, i'm buying another battery today to make it 3s2p configuration and change some mdf with balsa to lighten the weight.

As it is right now, the quad start to take off with just 40% of thrust and hover at 30% of power, at the cc3d gcs, i set the max throttle at 60%, so even i push the stick all the way up, it only give 60% of power.

The props i'm using right now are not even CF heheheh, it was plastic props. It was a nightmare when i tried to balance it, but the 9x6 sounds good, maybe i'm gonna cut the spare 10x6 prop to 9x6 and give it a try. I had ordered the wood props from hobbyking, it will arrive in about 2 weeks
 
Herpderpwerp said:
The one that getting hot are the cables, the one that attached to the battery and the xt60 connector. I think the amps draw are a bit high, i'm buying another battery today to make it 3s2p configuration and change some mdf with balsa to lighten the weight.

As it is right now, the quad start to take off with just 40% of thrust and hover at 30% of power, at the cc3d gcs, i set the max throttle at 60%, so even i push the stick all the way up, it only give 60% of power.

The props i'm using right now are not even CF heheheh, it was plastic props. It was a nightmare when i tried to balance it, but the 9x6 sounds good, maybe i'm gonna cut the spare 10x6 prop to 9x6 and give it a try. I had ordered the wood props from hobbyking, it will arrive in about 2 weeks
Click to expand...
Check your soldering, you probably have a cold joint giving resistance. I have found that any worthwhile CF props are expensive and wood is as good as CF IMHO and a lot cheaper.
 
GJH105775 said:
Check your soldering, you probably have a cold joint giving resistance. I have found that any worthwhile CF props are expensive and wood is as good as CF IMHO and a lot cheaper.
Click to expand...
Roger that, i will check the soldering when i put the extra conector for parareling the battery.
 
After a few frame built, finally came up with this design, i'm able to cut the weight from 2500grams to 1800 grams, and maximize the flight time from 5 minutes to 9 minutes. Using some leftover acrylic from my workshop and using a servo to stabilize the camera.

Now trying a multiwii fcb coz cc3d doesn't have an altitude hold feature. (The multiwii hasn't been instaled yet)
The center of gravity is slightly off to the front, maybe gonna change the design for 1 more time to move the middle arms slightly to the front to have better ballance

P_20150815_133225_2.jpg
 
Jackson said:
Can't you just shift the battery a tad?

You may want to look at ReadyToFly's offerings.
http://www.readytoflyquads.com/flight-controllers/flip-series


Your new build looks pretty cool. :)
Click to expand...
The thing is, i made a cut under the body tha the battery can sit perfectly so it wont shifted during flight, but i miscalculated the front being heavier because of the camera and gimbal. The current fcb (cc3d) still can compensate for it but i think in a long term it will stress out the front motor more.
This is the cut i made for the battery
P_20150815_195738.jpg P_20150815_195840.jpg
 
You must log in or register to reply here.
Back
Top