Can somebody please look over my parts list to see if the quadcopter would function..

C

Chester (newbie)

Member
Hi,
I've been considering building a drone for a while now and have finally come up with a parts list for my build. If somebody would be kind enough to see if these components would work together, that would be very helpful. Feel free to comment on the build giving me positives and negatives.
The parts list is,

http://www.hobbyking.com/hobbyking/store/__9183__Turnigy_5000mAh_3S_25C_Lipo_Pack.html

http://www.hobbyking.co.uk/hobbykin...AWG_silicon_wire_10cm_ESC_side_5pcs_Bag_.html

10 inch propellers but not the dji ones because they won’t fit the motors
http://www.hobbyking.co.uk/hobbyking/store/__25824__10x4_5_SF_Props_Black_CW_2pc_CCW_2pc_.html

http://www.amazon.co.uk/Foxnovo-Dig...28597427&sr=8-1&keywords=lipo+battery+charger

Servo Leads
http://www.ebay.co.uk/itm/10X-Male-...559?pt=LH_DefaultDomain_3&hash=item4d3058899f

http://www.hobbyking.co.uk/hobbykin...e_5_8Ghz_200mw_FPV_Wireless_AV_Tx_Rx_Set.html

http://www.hobbyking.co.uk/hobbykin..._Polarized_SpiroNet_Antenna_V2_RHCP_SMA_.html

Flight controller - DJI NAZA M-LITE WITH GPS - http://www.ebay.co.uk/itm/251898393891?_trksid=p2055119.m1438.l2649&ssPageName=STRK:MEBIDX:IT

Frame - HobbyKing Q450 http://www.hobbyking.com/hobbyking/...opter_Frame_450mm_Integrated_PCB_Version.html

Landing extensions

Controller (Transmitter) - Turnigy 9Ch http://www.hobbyking.com/hobbyking/..._Module_8ch_Receiver_Mode_1_v2_Firmware_.html

Speed Controller x 4 - HobbyKing 30A blue series - http://www.hobbyking.com/hobbyking/...0A_BlueSeries_Brushless_Speed_Controller.html

Motors x 4 - NTM Prop drive - http://www.hobbyking.com/hobbyking/...00W_Brushless_Motor_short_shaft_version_.html

FPV COLOUR MINI CAMERA OFF OF EBAY - http://www.ebay.co.uk/itm/391053538232?_trksid=p2055119.m1438.l2649&ssPageName=STRK:MEBIDX:IT

BRUSHLESS GIMBAL CAMERA MOUNT - http://www.ebay.co.uk/itm/321643309523?_trksid=p2055119.m1438.l2649&ssPageName=STRK:MEBIDX:IT

TRANSMITTER AND RECEIVER - http://www.ebay.co.uk/itm/251629978011?_trksid=p2055119.m1438.l2649&ssPageName=STRK:MEBIDX:IT
Thank you
 
I suggest you get and stick with XT60 connectors, and unless you decide to do an octocopter or maybe hexacopter (depending on the motors) I would suggest sou get this battery made by Turnigy, under their Multistar line. It is lighter as it has a lower C rate. 52 amps constant and 104 amps @ 10 second burst.

Take a look at this thread for the FPV parts, might see some cheaper or some better options for FPV equipment.

You should need some male to male servo leads to plug the receiver into the flight controller. And if you do decide to switch over to XT60 connectors, it is not a really big deal, but saves some soldering as XT60 is probably the most popular currently, followed by the deans.
 
Hi mate George covered all I was going to say but the HXT 4mm connectors is a big over kill they are rated at 96 amps ,if you using them to connect motors there are lighter ways to do this like a break out loom from hobby king , if any of you guys are going High Voltage for multi rotor set up look at AS150 anti spark rated at 150 to 170 amps , the new XT90S the S has an anti spark and will also do 150 amps
 
Back
Top