Recent content by Shuff

If the esc units will work with a Naze 32 FC I might put in a new PCM radio and a Naze 32 FC which I happen to have spare.

All, A cx20 (zero) which has some issues after a crash, has come into my posession. I am trying to find out if the Cheerson esc units are compatible with a Naze 32 FC. Currently the craft just beeps when powered on and the GPS plug is not connected as I don't know which way round it plugs in...

Hi, yes I have and their wiring diagram for the gps is different. I will open the flight controller box to see what type of board is in it. And see if I can't find some info on it.

Yes , done that however there is not much info on that particular version. If it turns out the FC is unrepairable I do have a KK215 control unit or a Naze 32 I could fit . I could do with finding out what esc units are on the craft.

Hi All Just been given a CX20 (Zero Tech ). I am looking for some info on the flight controller ie what type is it ? The previous owner disconnected the 6 pin (2x3) GPS plug and I dont know which way to plug it back in . The Controller is just a little white box , no lables apart from a...

Hi All I have built my own craft before but am fairly new to the scene (250 racing quad Naze32) . This week I have been given a CX20 Auto-Pathfinder 6-Axis system drone. The guy who gave it me knows noting about them and he crashed it !! He replaced the motors for a suitable replacement ( XT...

Hi Folks, I have just fitted a GPS module to my Naze 32 rev 6 board (CF FW 2.3.2) and am trying to configure the setup without much luck. The GPS has a good signal and the flasing LED on the GPS indicates a lock, the wiring GPS TX goes to Naze RX in , But I need advice on configuring the...

Hi all, Having built my 250 quad around the Naze32 rev6 FC, I am wondering if there is any advantage of adding a gps to the model. The fc does not have the full suite of sensors, ie no barometer. Thanks for any advice.

Hi folks, my current transmitter is a Spektrum DX6i which I have for 2 models. I have never really been happy with the DX6i because of its cheap looking plastic case ,many years ago I used Futaba gear which I liked. Recently I spotted an Aurora 9 transmitter for sale and am now considering...

Hi Folks, I am wondering what motors to fit to my 250 carbon fibre quad (with current motors it weighs in at about 500G). The current motors are only 980KV and wont lift the quad, someone suggested 2500kv , I am looking around for Turnigy 2206-2500KV but Hobbyking dont have them in stock yet...

Ok guys , Thanks for the info . I only followed the vid for the Naze32 setup , The motors I used were some from a project which I started a few years back but never finished but someone on here said they would be ok for my 250 build ( but obvious now they ar enot) Currently trying to source some...

Hi Folks, Just in process of building and testing my quad, my components are 250 fibreglass frame, multistar 2209-980 v2 motors with Gemfan Tri 5030x3 props. Esc,s are multistar 12A race spec 32bit opto with Naze32 rev6 fc. Redcom cm703 receiver and XT60 PDB, Lipo 3S 11.1V 1500 battery. Total...

Hi Folks, I have a programmer for a 30A Plush esc, its white with " turnigy programming card" written on it. Will that programmer work on my new multistar opto esc units ? Or do I need to buy a new programmer . Thanks for any info.

Hi folks, Just started to build my quad using some parts I ordered about 5 years ago. I have come to realise things have moved on immensely in that time. In my inventory I have some Turnigy motors and matching Plush 30 ESC,s a kk215 fc with a Spektrum Ar610c , transmitter is Spektrum Dx6i. The...

Hi Badfish, Thanks for the info. I will probably get some smaller motors in the near future. I have some Plush 30A ESC units but I'm not sure if they are compatible with the mentioned motors ? A lot has changed in the last 5 years since I originally thought of building my own.