Recent content by C.B. Russell

  1. C

    Autonomous Quad

    Built three INAV quads and then got Holy Stone HS720E 4K! I’m very pleased with it but… I wish I could get my other three DIY drones to handle like it does. Is this possible through software end or somehow? Thanks
  2. C

    INAV in depth settings

    INAV in depth settings I have built the TCMM Tyro 119 DIY 3-6S 6" Quad Kit (with a little customization concerning cam mount and compass mount for BN 880) and… I have also built another using the same flight stack with a different more customizable frame but… I need a little more in depth...
  3. C

    Flysky FSi6x and INAV Setup

    Anyone know of an in depth setup tutorial for INAV and the FlySky FS-i6X? I was going with the Joshua Bardwell setup but he lost me at the receiver part. Thanks
  4. C

    Flight Controller Heating up bad?

    No, cannot connect to betaflight. In fact I can only use USB for a moment before it gets hot.
  5. C

    Flight Controller Heating up bad?

    T-Motor F7 Flight controller heating up when it get any power? When I plug battery in wild beeping ? Any info? Thanks C.B.
  6. C

    Scratch Build - T-Motor F7 Stack - F7 FC, F45A V2 3-6S 4-in-1 ESC Combo

    Hey guys, TBS Unify EVO 5.8GHz Video Transmitter is getting really hot, how can i change or fix this, it is jumped to battery and I'm looking for a 12v connection on FC.
  7. C

    Scratch Build - T-Motor F7 Stack - F7 FC, F45A V2 3-6S 4-in-1 ESC Combo

    K, went ahead and found video on this, bridged this to "always on" and it fired right up. Still got some bugs but all the pretty lights are on as they should be and getting video feed to monitor. Now it's on to Betaflight set up and calibration. Thanks A Bunch!
  8. C

    Scratch Build - T-Motor F7 Stack - F7 FC, F45A V2 3-6S 4-in-1 ESC Combo

    What about pit mode jumper?
  9. C

    Scratch Build - T-Motor F7 Stack - F7 FC, F45A V2 3-6S 4-in-1 ESC Combo

    Not getting any voltage from VTX pads.? Cam and Receiver show 5v.
  10. C

    Scratch Build - T-Motor F7 Stack - F7 FC, F45A V2 3-6S 4-in-1 ESC Combo

    VTX is jumped to battery.
  11. C

    Scratch Build - T-Motor F7 Stack - F7 FC, F45A V2 3-6S 4-in-1 ESC Combo

  12. C

    Scratch Build - T-Motor F7 Stack - F7 FC, F45A V2 3-6S 4-in-1 ESC Combo

    TBS Unify EVO no power?
  13. C

    Scratch Build - T-Motor F7 Stack - F7 FC, F45A V2 3-6S 4-in-1 ESC Combo

    Got it together while waiting on your response and hooked up to betaflight configurator. I'll see how it works and checks. Had to print out custom cam and board mount. We'll see.
  14. C

    Scratch Build - T-Motor F7 Stack - F7 FC, F45A V2 3-6S 4-in-1 ESC Combo

    Good morning. K , the TBS Unify EVO takes 7-26 volts, VTX jumper bridged to battery, yellow wire connected to Video out and +/- (Red /Black) respectively. I understand this but…three other wires go to camera directly (Not used as cam it connected via cam section) and two wires (Red And Green)...
  15. C

    Scratch Build - T-Motor F7 Stack - F7 FC, F45A V2 3-6S 4-in-1 ESC Combo

    Yep, that's what I was saying earlier!Different ways to connect. He is the one I've watched most. But... any info on the TBS Unify EVO connections with the wires that came with it?
See more
Top