New build

[yupiter00]

Hello everybody!
I have a probelm with my first build copter which is when try to fly the copter go around when is in air it is frustrating anybody can give me an advice how to solve this problem?
Second I use GEMFAN 5030 propps how to position in colors?

 

[ringolong]

Do you have a video? Did you calibrate the radio?

 

[yupiter00]

Do you have a video? Did you calibrate the radio?

Video I will do tomorrow...What mean about calibrate the radio?

 

[ringolong]

It sounds like the radio needs to be calibrated if it is spinning in a circle. You should be able to do it in your flight controller software.

Which flight controller are you using?

 

[GJH105775]

Hello everybody!
I have a probelm with my first build copter which is when try to fly the copter go around when is in air it is frustrating anybody can give me an advice how to solve this problem?
Second I use GEMFAN 5030 propps how to position in colors?

Also make sure your motors are spinning the right ways with appropriate props, if you put them all CW or all CCW the copter will do that.

 

[yupiter00]

It sounds like the radio needs to be calibrated if it is spinning in a circle. You should be able to do it in your flight controller software.

Which flight controller are you using?

CC3D and openpilot for configuration

 

[yupiter00]

Also make sure your motors are spinning the right ways with appropriate props, if you put them all CW or all CCW the copter will do that.

I think the propps positions are ok because fly up

 

[GJH105775]

I think the propps positions are ok because fly up

But what are they? It can go up if you have the props/motors all CW or all CCW, however it will YAW pretty fast.

 

[yupiter00]

video about the probelm it is hard to get up when try with little to higher throttle get this...
http://s12.postimg.org/kvx7fshtp/image.jpg
http://s12.postimg.org/hnsq2qvjx/image.jpg
About my copter

 

[yupiter00]

And anybody can give me advice why flips before flying with 3 part proppeler?

 

[ringolong]

Center the weight, tighten the props so that they will not spin off, try again, and report back.

 

[yupiter00]

The props spinning off is solved now needed to harder wring a nut.
But what about flying up instead of ahead?

 

[ringolong]

Center the weight of the quad. Hold it in the center while picking it up and both ends should balance. Move the battery further forward. Also, that is a large battery for a 250

 

[Jackson]

Battery is RED area. Using such a large battery I would suggest you remove the little camera plate or mount the battery underneath.

 

[yupiter00]

Center the weight of the quad. Hold it in the center while picking it up and both ends should balance. Move the battery further forward. Also, that is a large battery for a 250

I such centered the battery but same problem have with handling when try to fly...With little throttle go ahead and if increase it no go up only ahead...If starting but mucher throttle topp up the copter...Need an ESC calibration?

 

[yupiter00]

Battery is RED area. Using such a large battery I would suggest you remove the little camera plate or mount the battery underneath.

thanks it is good

 

[ringolong]

The escs and radio all need to be calibrated. Did balancing help any?

 

[yupiter00]

The escs and radio all need to be calibrated. Did balancing help any?

For esc how many beep means it is calibrated?And how to calibrate radio?
About balancing such I cannot seen anything because when try to fly its go ahead and not up immadietly.

 

[yupiter00]

The escs and radio all need to be calibrated. Did balancing help any?

Esc calibrated via Librepilot now is flying up and ahead but when try to get another side throwing into earth...How radio can calibrated could you write down his steps?

 

[ringolong]

What radio do you have?

Can you post a video of what it is doing for us?