Hello everyone,
First time post, first 250FPV build. My setup consist of
1 x ZMR250 CF Frame
4 x DYS 1806 2300kva motors
4 x SimonK 12 Amp ESC
1 x Multirotormania Power Distribution Board
1 x Dragon32 Acro Flight controller(Naze32 clone)
1 x Sony 600tvl super HAD board camera
1 x Boscam 305 Video Receiver
1 x Boscam TS5823 Video Transmitter
1 x HK 2.4Ghz 6Ch Tx + RX V2-Mode 2
1 x Turnigy nano-tech 1600mah 3cell 11.1
1 x 7” video display
4 x 5030 plastic propellers
1 x XT60 power connector
Since I am new to all this, I decided to try and spend as little as money possible, thinking that might have been a mistake on the HK 2.4Ghz 6Ch Tx + RX V2-Mode 2 , besides the point. I am posting today because I have a problem. I recently finished building my first 250FPV quad, yeeeeee. After hooking up the flight controller to the receiver and the esc’s as well to the flight controller, I then plugged in power and turned on transmitter, throttled up and unfortunately nothing. Roll, pitch, yawl, still nothing, nothing seems to be relaying/receiving the signal. I rebound the transmitter to the receiver and still nothing, which I do know they are bound, I hooked up a servo and tested it and it worked, seems not to be the problem. After messing with the 3 wire servo connectors, swapping, replacing, jiggling, etc. nothing still. After doing research I discovered the cleanflight app. I then connected my quad to my computer and connected to the cleanflight app. To my avail, it recognized my quad, receiver, motors, etc. I then proceeded to use the motor testing tab, which seem to work fine, all spin and seem to be in the correct direction. I then started looking at the receiver tab on the cleanflight app, noticing everything seems to be working as well, all corresponding with what I am doing on the transmitter, showing up in real time on the cleanflight app, throttle, yawl , etc.. So now I am stuck, I cannot figure out why my transmitter seems to be sending the signal to the receiver, which sends signal to flight controller, but it is not relaying it to the esc’s, Hahahah, if that makes any since, sorry new to all this again. Is it requird to arm the board or something of the manner? I desperately need help, as I have no one here in town that I know, could help me with this issue. I greatly appreciate any ideas or comments ASAP, as I would like to go out and fly this awesome little machine.
Thank you so much for any help
Thanks
-Brandon
First time post, first 250FPV build. My setup consist of
1 x ZMR250 CF Frame
4 x DYS 1806 2300kva motors
4 x SimonK 12 Amp ESC
1 x Multirotormania Power Distribution Board
1 x Dragon32 Acro Flight controller(Naze32 clone)
1 x Sony 600tvl super HAD board camera
1 x Boscam 305 Video Receiver
1 x Boscam TS5823 Video Transmitter
1 x HK 2.4Ghz 6Ch Tx + RX V2-Mode 2
1 x Turnigy nano-tech 1600mah 3cell 11.1
1 x 7” video display
4 x 5030 plastic propellers
1 x XT60 power connector
Since I am new to all this, I decided to try and spend as little as money possible, thinking that might have been a mistake on the HK 2.4Ghz 6Ch Tx + RX V2-Mode 2 , besides the point. I am posting today because I have a problem. I recently finished building my first 250FPV quad, yeeeeee. After hooking up the flight controller to the receiver and the esc’s as well to the flight controller, I then plugged in power and turned on transmitter, throttled up and unfortunately nothing. Roll, pitch, yawl, still nothing, nothing seems to be relaying/receiving the signal. I rebound the transmitter to the receiver and still nothing, which I do know they are bound, I hooked up a servo and tested it and it worked, seems not to be the problem. After messing with the 3 wire servo connectors, swapping, replacing, jiggling, etc. nothing still. After doing research I discovered the cleanflight app. I then connected my quad to my computer and connected to the cleanflight app. To my avail, it recognized my quad, receiver, motors, etc. I then proceeded to use the motor testing tab, which seem to work fine, all spin and seem to be in the correct direction. I then started looking at the receiver tab on the cleanflight app, noticing everything seems to be working as well, all corresponding with what I am doing on the transmitter, showing up in real time on the cleanflight app, throttle, yawl , etc.. So now I am stuck, I cannot figure out why my transmitter seems to be sending the signal to the receiver, which sends signal to flight controller, but it is not relaying it to the esc’s, Hahahah, if that makes any since, sorry new to all this again. Is it requird to arm the board or something of the manner? I desperately need help, as I have no one here in town that I know, could help me with this issue. I greatly appreciate any ideas or comments ASAP, as I would like to go out and fly this awesome little machine.
Thank you so much for any help
Thanks
-Brandon