Search results

Hey this is a sunset I filmed yesterday with my homemade quad. Im pretty happy with the gimbal but its not perfect, anyone know what to tweak to fix the tiny vibration that appears once or twice throughout the vid? Thanks in advance :) PID P[ 4.6, 170, 0.07] I[5.5, 195, 0.09]...

Hi guys, Iv been messing around with this 3 axis gimbal i got and i cant seem to get it working. Using V096 and the v1.31 board, i can connect to the GUI and everything goes green. However as you can see in the pictures it says IMU not available. I have triple checked that the IMU is properly...

The gimbal is the storm32 3 axis from ebay. I haven't used it yet, only uploaded the bootloader. I'm using a gopro hero which doesn't fit into the gimbal so I modified it so it would fit. I 3D printed a piece to drop the platform which the camera rests on down about an inch and out about an inch...

Hi guys, so I havent flown my quadcopter in about 7 months and my Lipos have been in my room untouched since. I was just wondering, as Im about to start flying and filming again, is there anything I should do before I use them or charge them again? My charger is the Turnigy Accucell 6. The...

Hello so I think im having problems with connections between my tx and rx for my quadcopter. Its a turnigy tgy-i6 and tgy-ia6 receiver. Basically the rx signal drops to zero and sometimes disappears off the screen on the tx at only a few meters distance but the quadcopter still responds to...

Hello, Im currently in the part choosing stage of building a 250 fpv racing (fun racing not competitive) quadcopter. Iv already built a 500mm quadcopter so I know the basics but I'm stuck on what ESC I should get for my 250. I have chosen the Emax Mt2204 II 2300Kv Cooling series motor. I will be...

So iv crashed my quadcopter many times, however the last two times have been the exact same but i cant figure out the cause. I suspect its a possible faulty esc. Im using 20A Afro ESC. Both times i was flying for longer than usual, 10min<. Both times I was flying aggressively during the flight...

Hi I was just wondering if it is possible to control a servo using the potentiometer on my tx. It's a tgy i6. My fcb is the CC3D. If it's possible, how would I go about it? Do I connect the servo to the reciever or the flight controller? My reason for wanting to do this is so I can mount my...

So iv 3D printed a 2 axis servo gimbal for my quadcopter. I have put it all together only to realise one problem. How do you get the servo that controls the roll to have a strong and secure connection to the rest of the gimbal?? For example https://i.ytimg.com/vi/dOu_MZyWr8w/maxresdefault.jpg...

For high altitude fpv flight.. Would it be better to have your fpv camera facing forward or facing straight down? I presume you don't get to see how much you're drifting away if you're high up and your cam is facing straight ahead.. Could be deadly for losing signal.. Thanks in advance

I'm very conscious of running out of range with my quad and was wondering what kind of distances ye get with the tgy i6? As it has no fssi. Thanks

So when I was flying my s500 today with a 4s 5200Mah lipo and 935kv motors I decided to have some fun and go full throttle a few times starting from just a few meters off the ground. All was well except as the quad rockets upwards on full throttle it goes quite a bit off course, as in doesn't...

So I bought the eachine ET200 VTX with VC700 TVL CCD CAM and use it with the RC832 VRX. I also have these http://www.banggood.com/Boscam-SKY-FPV-5_8GHz-Petals-Clover-Mushrooms-Antenna-RP-SMA-Male-p-91109.html clover antennae. I'm getting roughly 60m range before my Quanum V2 Goggles go fuzzy...