MHQ2 build but i cant figure it out im very new

[Dylan McQueen]

I printed out all the parts and bought the 3s kit which had everything but receiver and fpv. This is a receiver my dad let me use but I've tried a lot of different things but i just cant seem to figure it out. could anyone help me get this thing in the air i'm tired of just looking at a the quad laying on my table.

 

[GJH105775]

Hahaha, plenty of people here to help. What do you need in particular? How to wire it?

 

[Dylan McQueen]

Hahaha, plenty of people here to help. What do you need in particular? How to wire it?

Yeah it the flightcontroller gave me 3 female to female plugs and I've tried a few different things. I current separated the wires to try out a thing I saw on YouTube but it didn't work or there is another problem. I could easily put the wires back together if I needed to.
And thanks for the reply!

 

[GJH105775]

Here made a quick diagram, should prove helpful.

 

[Dylan McQueen]

My receiver isn't one like that it has like servo labels or something, I got it off a heli my dad had laying around and my fightcontroller only has 10 pens 5 on top and bottom it's an afroflight32

 

[GJH105775]

My receiver isn't one like that it has like servo labels or something, I got it off a heli my dad had laying around and my fightcontroller only has 10 pens 5 on top and bottom it's an afroflight32

Can you provide the model number of it and perhaps a picture?

 

[Dylan McQueen]

I took pictures and attached them when I made the post if that's not enough just tell me what I can do to help

 

[GJH105775]

I took pictures and attached them when I made the post if that's not enough just tell me what I can do to help

Oh, hahaha. I saw it when I first looked at the post, but forgot about it haha. I see, your question is about the channel for the control.


AIL = CH1
ELE = CH2
Throttle = CH3
RUD = CH4
AUX = CH5
GEAR = CH6

 

[Dylan McQueen]

Thank you But what do I hook them to in the flightcontroller? It's a afroflight32 and it only has 10 pins 5 on top and bottom? Sorry I'm so new

 

[GJH105775]

Thank you But what do I hook them to in the flightcontroller? It's a afroflight32 and it only has 10 pins 5 on top and bottom? Sorry I'm so new

Can I get a picture of the bottom? It probably only requires signal and ground, but a look at the bottom of the board should verify that..

 

[Dylan McQueen]

Can I get a picture of the bottom? It probably only requires signal and ground, but a look at the bottom of the board should verify that..

I'm at work I'll send one as soon as I get off

 

[Dylan McQueen]

this is the bottom

 

[GJH105775]

this is the bottom

Looks like you need an SBUS or PPM Rx


http://aerialfreaks.com/upload_file/upload/NAZE32_RADIOGEAR_SETUP.pdf

 

[Dylan McQueen]

ive hooked it up how i understood it but i still get nothing when i plugged in the battery the receiver light wasnt lit up or very dem. i matched the channels to the matching receiver things.

 

[GJH105775]

I don't believe that your receiver is SBUS, I am going to look to see if it is, if not you can get a converter or different receiver. Yours is probably PWM.

 

[Dylan McQueen]

i have no idea honestly im super new. im fine with buying anything i need im so ready to fly

 

[GJH105775]

I believe that this may be what you need.
http://www.hobbyking.com/hobbyking/..._DSM2_Compatible_7Ch_Receiver_w_Failsafe.html

 

[Dylan McQueen]

so what should i buy?

 

[GJH105775]

so what should i buy?

That receiver will receive the signal from your spectrum Tx and it will output SBUS.

 

[GJH105775]

Allow me to verify that this flight controller uses SBUS 100% for sure before you buy anything as I don't know for sure.