KK 2.15 ESC's Beeping Problem...Needs Solution..!

U

Umair Shah

New Member
Hi,
Friends..!
I am new here...I am building my first Quad but I am having issue..I am using following items :
1) 30A ESC's
2) 2212 1000 KV Motors
3) KK 2.15 Flight Controller
4) 4 Channel Transmitter & 7 Channel Receiver (Dynam Brand)
When I connect my ESC with my Receiver directly so ESC is working fine..The Motor is working..!
But when I connect ESC's into KK 2.15 and then power on so no ESC works and Motors are not working..Instead all at once I hear some beeps from all ESC's at once which keeps continuously beeping..I am really in trouble here..Needs solution..!
Also I have tried with ESC Calibration in KK 2.15 that is also not working out as when I press 1 & 4 Button and then power on the Transmitter and KK Flight Controller then so keeping my throttle at full and then when I move down the throttle so nothing happens and the ESC's keep beeping like that...!
So if you people can please let me know that what I am missing or what I am doing wrong will be really great..!
Also I have uploaded video to YouTube so it will be easy to watch that video and then look at my post you will better know please :

Waiting for your reply..!

Kind Regards,
Umair Shah Yousafzai
 
That sound is saying that it is in standby and ready, have you tried to disarm the KK board? Go into your settings and under receiver test make sure that all of your sticks are the right way and at 0 (you will do this before every flight).

To arm it hold the left stick (mode 2) down and to the right, and to arm it again, down and to the left.
 
Well...Thanks for your reply..As to KK Board power is only provided through first ESC so that why..! Actually there was other issues as somone told me to remove the red power wire from other ESC's made my one ESC Bad one...I am thinking I should really stick with all red ones plugged in for now...Also when I plug out my red wires from other 3 ESC's than 1st one so than that first one ESC gets too hot and became a bad ESC..so now I am in loss due to one Bad ESC too..! the rest is working fine now..! All props were reversed I corrected them also wires on the KK Board were reversed I fixed them...Also my transmitter isn't compatible with my ESC's so calibration do not works..! that's why I can't fly it now..!
 
Umair Shah said:
Well...Thanks for your reply..As to KK Board power is only provided through first ESC so that why..! Actually there was other issues as somone told me to remove the red power wire from other ESC's made my one ESC Bad one...I am thinking I should really stick with all red ones plugged in for now...Also when I plug out my red wires from other 3 ESC's than 1st one so than that first one ESC gets too hot and became a bad ESC..so now I am in loss due to one Bad ESC too..! the rest is working fine now..! All props were reversed I corrected them also wires on the KK Board were reversed I fixed them...Also my transmitter isn't compatible with my ESC's so calibration do not works..! that's why I can't fly it now..!
Click to expand...

What transmitter/reciever d oyou have? Is it PPM, or PWM? and regarding the red wires; it does not really matter, if it gives you problems you can unplug them, I leave mine in the cable, as I don't want to worry about something causing it to short if the wire gets out of the tape or heatshrink.

What do you mean that you reversed wires on the KK board? The plug should be made up, and the ground wires are always toward the closest edge of the board. The 5v+ (red) always is in the middle of the plug.

Are all of the motors spinning the correct way?
 
Be careful with the cheap motors, they like to fail if you run them hard and the leads will break off or you handle them ruff, jsut keep that in mind.
 
Back
Top