Recent content by miky94

as I heard that 4S ESC is a little close to the edge and the motors are 6S rated I bought that 6S ESC for future upgrades even if probably I'll have to buy a 6S rated FC but in this case I think the motor wire broke and then the ESC burnt, I don't think the bigger ESC would have survived anyway

I reconnected the broken wire of the motor and now on another esc it works! but if I wire a working motor on the other esc it behaves like in the video, no chance to repair the esc? if i have to replace it, an higher current and higher voltage rated esc would be more durable? or in that case...

yes I'm trying to learn something on youtube :) in the image you can see the broken wire, I took off half turn of winding because it was too short, but as it is insulated copper wire I don't know how to test the solder joint

yes I tried but it is the motor, in the long waiting for a new one do you think it is worth to try rewiring it? I soldered the broken one but I don't know if I did it right

hi all, after a crash (but on the other side) a motor doesn't spin anymore, I checked and there isn't continuity between power in wires and the esc outputs, but also there wasn't continuity between one wire of the motore and the others two so I saw that it broke off on the side of the motor, I...

I had a new flywoo, again I flew for a while and then same problem. this time the receiver was isolated and no water on the grass. I must say just before the problem I crashed the antenna from 1m high on concrete but externally I don't see any damage and I flew slowly with 600mw but it is 0 °C...

about the battery, the Explorer mounts this stack https://it.banggood.com/16x16mm-Flywoo-Goku-F411-Micro-Stack-F4-V2_1-Flight-Controller-and-BS13A-13A-BL_S-2-4S-4in1-ESC-Flytower-for-FPV-Racing-Drone-p-1615281.html the ESC has 15A burst current and the FC has 2A BEC, considering a little...

let's see if banggood replaces it to me, sometimes I also noticed the screenshot attached, as if the camera wasn't working

I'm sorry for that I updated the links you can watch the videos now As you will see the OSD is present but the signal is weak so I think the problem is in the VTX but don't know how to diagnose

I definitely have a problem with the video signal, you can see the difference between 1st and 2nd video, I don't remember crashes in between but since the receiver has diversity, I tried all the antennas combinations and the OSD disappears along with the video I think the problem could be in the...

Yes of course 2 differenti issues about the video even if I flown slow the cold should have helped not damaging the VTX, which I tried at home and works about the control I bought TX and RX together so the tuning should match, unfortunately FlySky limits the choice but let's see if the new...

No I meant on the video receiver, on the VTX I have the Flywoo antenna which is for long range, today I tried with 2 Eachine K-Loverleaves on the ROTG02 but even outside the building I couldn't get a reliable signal, it is surrounded by portcullis and so maybe flying close to it 600mW works...

about the FPV system, now I'm flying with the ROTG02 with 1 Eachine dipole and 1 Eachine K-Loverleaves antennas and it is not bad but because of rain I'm flying in an empty covered market and sometimes I can't get a stable signal or I get a grey screen, maybe there is interference, anyway I'll...

you are right, the RSSI channel is AUX 8 that doesn't match any input on my TX and just stays in the middle (51%), I'll wire it on the new receiver, as maybe the weak link in the chain is TX - RX rather than VTX - OTG, I'll test it with the drone disarmed and also I'd test GPS hold as failsafe.

yes I don't know where that value comes from, bidirectional DShot is disabled in Betaflight, what about RSSI and link values? in fact to see below I had to pitch to the maximum