New scratchbuild V2:

X

X1XnobleX1X

Member
Hello!
I'm looking into buying the Diatone White sheep as my first build.
As I think the ZMR250 is a little too small, and the blackout 330 is a bit too expensive.

Is this frame kit worth getting?


Also, please look at my parts, over a month of two of research and trying to get the right parts, I think I'm ready to order.

These are my parts:
Frame : Diatone White Sheep PCB Version:
http://www.banggood.com/Diatone-Whit...-p-970933.html

Motor :SunnySky X2212 KV980 Brushless Motor:
http://www.banggood.com/Wholesale-Su...r-p-60600.html

ESC: Emax SimonK series (20A)
http://www.banggood.com/Emax-Simonk-...-p-918126.html

NAZE32 Full version - Already purchased

FPV Receiver: Boscam FPV 5.8G 8CH 200mW
http://www.banggood.com/FPV-5_8G-8CH...5-p-73203.html

FPV Transmitter: Boscam FPV 5.8G 200mW AV Wireless Transmitter TS351 :
http://www.banggood.com/Boscam-FPV-5...1-p-73198.html

Mushroom antenna: 5.8G Gain Petals Clover Mushrooms Antenna Set
http://www.banggood.com/5_8G-Gain-Pe...-p-919079.html

2.4G Receiver: FrSky D4R-II
http://www.banggood.com/FrSky-D4RII-...-p-929069.html

OSD: MinimOSD -
http://www.banggood.com/MinimOSD-MAV...d-p-73436.html

GPS: CRIUS NEO-6 V3.1
http://www.banggood.com/CRIUS-NEO-6-...-p-941832.html

FTDI Adapter: FT232RL FTDI USB
http://www.banggood.com/FT232RL-FTDI...-p-917226.html

FPV Goggles: Quanum DIY FPV Goggle Set with Monitor
http://www.hobbyking.com/hobbyking/s...arehouse_.html

Battery: ZIPPY Flightmax 2800mAh 3S1P 30C (Might get 3000Mah) X3
http://www.hobbyking.com/hobbyking/s...arehouse_.html

ZIPPY Flightmax 1000mAh 3S1P 25C - For FPV receiver
http://www.hobbyking.com/hobbyking/s...arehouse_.html

Transmitter: Frsky Taranis X9D+
http://www.perthrcvault.com.au/shop/...d-transmitter/
 
Jackson said:
Frame looks pretty, did you want one that big? ~480mm

Click to expand...
GJH105775 said:
If you have not bought the quantum goggles definitely get the version two.

Also what is the latest update?
Click to expand...

Running into a bit of trouble, and I'm worried!
Connected the motors to ESC and connected it to the power distribution board.
And plugged the signal wire into the Naze32.

Tested the Naze32 - No smoke. - Plugged in the battery no smoke.

Tried testing my motors, via the motor test in Cleanflight, none of the motors spun.

Since, I was following a guide, I plugged in the D4R-II as they had plugged it in first in the video. not sure if the D4R-II is powered, as no LEDs turn on, when holding the F/S button. - Still plugged into computer.

Am I missing something?

PLEASE HELP!

EDIT: Manged to bind the D4R-II to my Taranis, though Roll, pitch, Yaw, Throttle works, but the AUX channels don't move at all for any switch.

Any ideas?




 
Looking at your pic I see the RX pins are empty. I'm guessing you need to plug in your RX before moving to the next step.
 
Jackson said:
Looking at your pic I see the RX pins are empty. I'm guessing you need to plug in your RX before moving to the next step.
Click to expand...

Thank you for your advice, calibrated all ESCs and all of them worked, which is great!





EDIT: I can get it to arm. But the motors are not spinning at all? HELP!
 
Last edited:
You must log in or register to reply here.
Back
Top