First Quad Build, Help with parts.

S

Spitfire

New Member
Hey, im gonna start my first quadcopter build and im going to order everything of Hobbyking.com, i have chosen everything i think that's needed but im not 100% sure.

Here's my cart (if it works)
http://hobbyking.com/hobbyking/store/uh_showCart.asp?idproduct=19341&lasturl=

If it doesn't work, here's links to all the stuff

Frame
http://hobbyking.com/hobbyking/store/__42504__Hercules_500mm_QuadCopter_KIT_.html
ESCs
http://hobbyking.com/hobbyking/store/__2163__TURNIGY_Plush_25amp_Speed_Controller.html and a programming card.
Motors
http://hobbyking.com/hobbyking/store/__25076__NTM_Prop_Drive_Series_28_26_1100kv_252w.html
Props
http://hobbyking.com/hobbyking/store/__25819__10x4_5_SF_Props_2pc_CW_2_pc_CCW_Rotation_Blue_.html
http://hobbyking.com/hobbyking/store/__25821__10x4_5_SF_Props_2pc_Standard_Rotation_2_pc_RH_Rotation_Red_.html
Flight Controller
http://hobbyking.com/hobbyking/stor...ntrol_Board_With_6050MPU_And_Atmel_644PA.html
Batteries
http://hobbyking.com/hobbyking/stor...apacity_3S_4000mAh_Multi_Rotor_Lipo_Pack.html
Transmitter and reciver
http://hobbyking.com/hobbyking/stor...6_Model_Memory_Inc_7_Ch_Receiver_Mode_2_.html
Accessories
http://hobbyking.com/hobbyking/store/__19341__NTM_Prop_Drive_50_Series_Accessory_Pack.html
http://hobbyking.com/hobbyking/stor...JST_Plug_Quadcopter_Distribution_Harness.html
http://hobbyking.com/hobbyking/stor...ll_Checker_with_Low_Voltage_Alarm_2S_8S_.html


Do i have everything i need to start flying?

Thanks, Samuel
 
Hi Samual, good list the only thing is the motors are a high KV for a large quad 480 grms ( not flight weight just frame) , normally heavy lift quads use a low KV motor and big props your going to need a 12 inch prop to get the lift so your better off with a 650 kv this will spin a 14x5.5 prop and not get warm so a 12 inch prop will be ok
4 cell will be better than 3 cell but if you want a 3 cell then 5200mah will be better
get the Kk flash tool as the kk2.1.5 needs a better firmware to fly nicer
http://www.tjshobbies.co.uk/product_info.php?products_id=527&osCsid=hb999jm6li8h2unilleqq0t667
also your need male to male servo leads to connect receiver to FCB
Plastic stand offs for mounting the KK
heat shrink
 
holtneil said:
Hi Samual, good list the only thing is the motors are a high KV for a large quad 480 grms ( not flight weight just frame) , normally heavy lift quads use a low KV motor and big props your going to need a 12 inch prop to get the lift so your better off with a 650 kv this will spin a 14x5.5 prop and not get warm so a 12 inch prop will be ok
4 cell will be better than 3 cell but if you want a 3 cell then 5200mah will be better
get the Kk flash tool as the kk2.1.5 needs a better firmware to fly nicer
http://www.tjshobbies.co.uk/product_info.php?products_id=527&osCsid=hb999jm6li8h2unilleqq0t667
also your need male to male servo leads to connect receiver to FCB
Plastic stand offs for mounting the KK
heat shrink
Click to expand...

Thanks for the reply!
Ok, so i changed the motors to these, and i also changed my frame to this, it is a little lighter and in a X pattern. can i use 10 inch props to this frame or am i better off using 11 inch? It says that the frame can use 9~11 inch props. Changed the batteries to 4s 4000mah instead of 3s. This is the right flashing tool, right?
 
Hi mate yes yes and yes , one thing I will say is NTM motors are good and powerful but are not the lightest, also wires are stiff so dont bend them to much
 
You must log in or register to reply here.
Back
Top