cleanflight

I'm having issues with my quadcopter's motors. I'm using Racestar BR 2205 brushless motors, but when I mount them to the frame and test the motors in Cleanflight, they spin slowly and make a rubbing/grinding like noise (I'll attach a video). But when I unscrew the motor from the frame and test...

Hello, I was wondering if anyone here has some advice on which flight controller platform to use if I want to communicate with it live using a raspberry pi through some serial protocol (preferably mavlink). I've already looked at several, such as betaflight and cleanflight and they either...

Hi Guys, this is my 2nd racing quad I build, because I lost my first one in a neighboorhood. For my first one I had a FC, a PDB and used PPM to connect to the receiver. This time I went for a all in one board, with 4x esc, FC, and PDB, only problem what I'm facing right now is, this board...

I built my own quadcopter and I calibrated my ESCs all at once (with Cleanflight) and it worked. The motors are in sync when I let them spin using the Cleanflight interface (there is a throttle bar that you can pull up and down under the tab "motors"). But when I use my radio control to throttle...

I have the AT9 Transmitter and I am trying to set up an external receiver using the R9DS receiver. I can not use the built in FRSKY receiver because the AT9 can only bind to Radiolink receivers.... However, I having issues getting flight controller binded to the transmitter. The receiver is...

So I just recently got a C250 V2 Racing Drone and decided to get it set up with clean flight. I did everything the manufacture recommended for setup, however, I still have a major problem. The drone seems to lose its self-level over time. I'm not in manual or horizon mode because I have those...

I am new to drones and I have completed my build for the most part. I'm using a cc3d flight controller, a orangerx receiver and I have a dx6i transmitter. Everything seems to be working good and it connects to cleanflight and I can change all the settings. My problem is that my dx6i shows that...

Hello everyone! I am new to this forum and relatively new to building quadcopters. I just put together my first quad, not from a kit but with miscellaneous compatible parts and modifications. Everything has gone smoothly up until this point, and all of my connections are solid. However, I...

In my PID tuning tab,in PID settings I cannot put decimal values somehow! anyone has a solution for it?

Hello, I have a QAV-R with LUX FC and a DX6i transmitter/spektrum satellite receiver. On Cleanflight I calibrated my ESCs with a throttle max at 1850 (and min at 1030) because my DX6i seems to only give a signal from 1020 to 1900 in the receiver tab (with +125% expo). However eveybody seems to...

Hi! I'm at the end of my QAV-R build with a LUX FC and a SRX spektrum satellite but I have a final issue before making this beast fly. In fact in cleanflight on the receiver tab all my channels are illogically reversed. As an example moving the roll stick to the left on my DX6i increase the...

Help! This is my first quadcopter build and I am having an issue where I unplug the usb cable from my Naze32 rev6 (I am using cleanflight) and when I try to do anything on my transmitter, nothing happens. There is just a solid blue light. I have been trying to get this thing to work for three...

I have the FS-i6 transmitter and I am trying to map it in Cleanflight. I am having quite a lot of trouble. I have read many other forums, none of which have worked. Currently I am mapping like this: 4ARTE123 AND I have all of the channels reversed on my RX. This gets everything correct except...

Hi Guys. I just started getting into this hobby a couple of months ago and I'm trying to get to a good starting point with some help from experienced quad pilots. I just got a Taranis radio and d4r-ii working on my ZMR250 frame with a Naze32 and Cleanflight. So I've been wanting to know what...

Having used CC3D and KK2.1.5 - I thought it wise to try the Naze32 - which seems more widely used. I can and have updated it and used Baseflight...BUT for the life of me.. I cannot get it to load into Cleanflight. It does not auto connect and a manual connect fails after 10 seconds. Using...

hi guys You'll have to forgive means I'm new to quads but have been building and flying helis and planes for years. I've just finished building my new zmr250 with a full naze32 rev6. I'm trying to work in my Spektrum dx6 with an r615x in rd ppm mode but I'm lost on how to work in the throw...