Search results

Fellas, I have been thinking about when a person loses there drone. Why don't the manufactures put in a audible device say like a beep beep alarm that is activated by a button on your transmitter. You have an idea where your drone crashed but you cannot see it, just hit your alarm button it...

Fellas. I am thinking of getting a Chroma quad with a Spectrum DX4 tx. Horizon has it for $299.00 with free shipping. Question is the DX4 as good of a tx. as the Yuneece st10+ tx. and will the ST10+ work with the Chroma that already has the DX4 receiver installed in the Chroma. I know the...

Fellas, building a 600mm quad, new motors, esc's, kk2 board, wiring. Problem is, when first making sure motors all start at the same time, 3 of the 4 just sit there and kind of vibrate and hardly do nothing, while 1 works perfectly. This is my 5th quad build from a 380mm, 3-450mm and this...

Fellas, I have switched over from cc3d to kk2.1.5. Question is where or what cables do you use to go from the board to receiver. Where can I buy these cables. With cc3d they come with receiver cables but when I bought the kk2.1.5 board it does not come with cables only a buzzer. You would think...

Fellas, I have a Totem 380 quad with motors and esc's from a flying 3D X8 quad. I have Open Pilot board, Flysky TX and RX 2200mah lipo. Problem is, when programing the quad in open pilot, when it comes to arming the esc's they give out a melody then a steady beep, beep, beep. On my 450 quad the...

Fellas I have flying 3d x8 quadcopter. From the very start, it has not worked. I have watched every video, read the manual a dozen times and it has not flown off the ground not even once. The best it has done is spool up about half throttle and never has it lifted off the ground. Fully charged...

Fellas, a friend of mine has a new flying 3d x8 quad, he is having a problem getting it to arm and fly, I have read other forums on this quad and it seems, people are not happy with this bird. Firmware updates seem to not work, cracking of the plastic, etc. I am recommending sending it back to...

Fellas, I have 2 Imax B6AC clones. Problem with both is they both have lost there lipo function in the programing setup. Try and setup lipo in the charger it bypasses lipo and goes to either life, nimh, NiCad or pb. I have tried everything and cannot get the charger back on lipo. Is there a...

Fellas: I have a 450 Chinese quad that is tipping at takeoff. I have the battery mounted on top of the Quad. I see that some 450 quads are mounted on the bottom. Does it make a difference to where the battery is placed, or does it really matter. There is a thread and a video on how to check...

Fellas: Where is the best place to mount the control board on a 450 quad. Back of the frame, middle of the frame or front of the frame. It seems to me that it should be in the middle so it balances the quad as far as the hardware configuration on the computer. Is this true or does it really...

Fellas: I have a Chinese 450 quad, open pilot, flysky f's-t6 tx. With the open pilot firmware, everything went well programming the quad. Next the tx programed just fine, with no glitches. Problem I am having, is when I try and take off under full throttle the quad nose dives either forward or...

Fellas: I have a 450 Chinese quad, running open pilot cc3d board and trying to use a Futaba 6ex tx. On the open pilot site, quad setup was a breeze. The Futaba 6ex is not working out. When I try and Setup the 6ex, in open pilot, when it comes to setup the stick movements, the 6ex and open pilot...

I first bought a JJRC H5C quad with camera and transmitter, works fine. Then I bought a bare bones Syma X5C without camera and transmitter. The JJRC transmitter will not bind with the Syma X5C quad, is there a different 2.4ghz chip in the Syma vs. The JJRC, both quads are virtually identical...