Search results

connected to opentxcompanion and tried to change settings. Now when I turn on the radio it is in emergency mode and nothing works???

I have a radiomaster tx16s that has worked fine until I accidently put the display time on to 0, now I can't get to the setup page to change it because the display turns off immediately. Tried holding the menu button for long press - that does nothing. Had never used opentx companion before so...

Been working on this quad and have it bound and will arm and motors work at idle speed but when throttle is increased, the props spin faster then all motors stop as if they had exceeded some setting. Any thoughts on this? I've flashed the escs and FC..

just checked the rotation of the motors which should be outboard - motors 1 and 4 are going inboard and motors 2 and 3 are going correctly outboard - tried switching resource for motors but that didn't work = any thoughts? anybody out there?

One thought I had was to replace the cli dump of the f4 with the f7 cli dump - or would there be settings particular to the f7 that wouldn't work with the f4?

Got a GEPRC cinepro 2" and soon had problems with it burning out DSMX receiver, so I replaced receiver with TBS nano and the cinepro burnt that out too. So I got a GEPRC F4 fc and just finished installing it with a new TBS nano. The receiver is working the way it should but arming the quad...

Probably had the wrong settings for rssi in betaflight, got rssi signal back 99% by changing rssi channel. Now after fresh bind the motors start up at armk, and rev for 2 seconds then I get rssi lost in osd. Tried to take power off quad to let it cool, then tried arming and no motors. Rebind...

Did a fresh bind on it and got the motors spinning after arming but throttled up and it cut out and won't restart motors. Could it be that since the rssi appears to be 0, that the failsafe cuts the motors in the 2 seconds specified in betaflight setup? The betaflight still shows the radio...

Flew my new GEPRC CinePro 2" 4K F405 FPV Drone for 4 or 5 times, now there is 0 rssi shown on osd and motors won't start. Checked on betaflight and controls still respond correctly. I'm new to fpv, been flying fpv quads for 6 months now so not super knowledgable about a lot of the technical...

Thanks for your reply. The signal is low when tx is near or far. video appears out too now, mob might be fried. thanks again

Thanks, what length is the receiver antenna supposed to be? It seems to be solidly soldered. I can understand the signal being 0 if receiver got fried, but this is just sudden reduction from 80 to 10 so the receiver must still be good?

Just got it to bind, the usual way with frsky push bind button (I guessed where) and then power on. Thanks

My mobula 6 hd was working fine, now rssi is down to 12 and quad won't arm. There are 2 antennas on the board, one bare and one with insulation - I don't know which is receiving and which is tx. both seem to be solidly soldered. Any ideas?

Just bought GEPRC CinePro 2" 4K F700 with dsmx. There are no instructions on how to bind (no instructions at all). I am a noob, just fly tinyhawk 2 and freestyle, mobula6. Have absolutely no idea how to bind. Seems like some dsmx need bind plug (none provided) some enter bind on powerup, some...

Thanks for your help, I must have missed the mode setting. I got it to work by switching the channels around, albeit not the normal order. Still learning. Thanks again

Forgot to mention that I've never used the tx16 or a whoop before, just dji

Just signed up and have a question already. Trying to setup tinyhawk with tx16s and it binds ok,but the controls are messed up, throttle is on stick where roll should be, yaw is ok, elev and aileron mixed on sticks. Have skfly 8 set, any idea why? I can try to set the channels to correct...