Search results

On a different not i see that the new version of beta flight has a return to home via GPS i might just stick with Beta over INAV.

i flashed it with beta flight and have the exact same issue as soon as i plug in my LIPO it just reboots, arms the motor, reboots, I am starting to think i might have a defective 4 in 1 ESC.

I have not tried calibration, what is the procedure for that ? If it keeps acting up i might just flash it with BetaFlight and call it a day. I was liking the GPS features of INAV like RTH and loiter but it might not be worth the damn grief.

Hi got my new setup kinda running. I am using INAV when i plug in my lipo i can get the esc to arm. When i arm the controller and throttle up INAV reboots. I tried multiple different ESC protocols Standard, Multishot, OneShot. With standard the esc would not arm but with the others it does. As...

Flew it yesterday for around 10 minutes. Went great, nice and responsive. Next up add a FPV camera !

LOL i upgraded my reciever to the X8R so i can back feed telemetry to my Taranis X7. It seems to pair way faster and is a really nice unit

Ok i will check tonight to see if my BetaFlight F4 has that or if i need to add an SD card.

So I fly my S500 yesterday, F4 BetaFlight. Made sure the gyro was calibrates, made sure the failsafe was working. Took off and took it up to about 10 feet. It was stabe flew nice, I was praticing yawing and basic back and forth movment. The drone was very close to me and all of a sudden all 4...

Well learned a lesson, the ESC has three wires, signal, ground and 5v, the 5v is a BEC regulated output, not an input, I was hooking that wire up to the 5v out pin on the FC. might explain why i had so many off problems like the CLI screen locking up. I am going to retire this FC. I have a new...

I am going to try the work around calibration, but if it continues to give me trouble i can always order different ESC's. I would like to get these ones working since they came the motors.

Yes I have checked that box, I think what I need to do is go through the calibration process, full throttle battery unhooked, hook up battery, motor screen master slider to full, wait for beep, master slider to idle, wait for beep. When I hook up the battery now i get the self test tones and...

A servo test to get them going, can you elaborate ? Thanks!

yeah I think i might do that but vodka is the drink of choice. It is not arming, on boot up i can feel the motor twitching with the beep tones. I will figure out how to arm this thing tomorrow. Thanks

How can i make it arm, in beta flight i switched the warning switch and ran the master up and got no response. I am not using the X7 controller just the on screen software.

I will check it out. I am done tinkering for tonight. From what i can tell from the power on code i get the 3 power on beeps then the longer beep indicating connection to the FC. I have 11 volts on the positive to the ESC. I get no output. I am thinking its a setting for the ESC in betaflight...

yeah i have one motor hooked up on the bench to the ESC, when powering on i get the low med high tone, when i go into beta flight and arm the motors it does not spin. Very strange

When you say cross the wires to make it run opposite, you mean the A B C ESC output not the three control wires correct?

I got everything today, the ESC's have 3 small wires brown red orange, I am assuming brown is ground, red it power and orange is to the FC. Am i correct in this assumption. Also does anyone know with Betaflight and these ESC what mode to use DSHOT150 or something else. Thanks !

Yes they are all at 1500 on that screen, i will ignore the image of the drone moving. Thanks !

I have a X7 controller, BetaFlight F4 FC and a FrSky transmitter/receiver When i go to the receiver screen the image of the drone it slowly pitching up and and over. I assume i need to trim out the pitch somehow, what is the way that is done. I was looking through all the setting and nothing...