Search results

I ran both off the fc 5v n grn pad n it worked so it doesnt matter how u run the 5v n gnd. I just didnt know if they had to be ran like the led signal wire inline like 1 2 3 4 5 6.

Thats what im asking, if it matters where the power comes from for the led strips. havent seen any vids of led strips without the strip being able to power the next strip so didnt know if the power has to go inline of all leds being hooked up like the signal in n out inline

I am running in to the plug but trying to go to another one of these n dont know where to get power to it? Do u mean run 2 red power wires off the led 5v pad on fc. I want to do it like that but dont know if i can.

Picture shows 2 ways to wire n i dont know which way i can do it? Trying to use these 2 leds but dont know how to connect the power wire from one to the other cuz theres not a power in n out like all other strips. They were all connected in this huge pcb. In picture which way can i run power to...

In picture i drew the power wire n tryin to figure out which way to bring power over to another one of these blue arrow or yellow arrow? Im pretty sure i can do either way but dont know 100

Never mind finally got it had to change the battery settings for the alarm to internal instead of external

So i got a flysky x6b receiver n flysky i6 radio n i tried to bind it on my new build n the radio keeps beeping until i unplug power to receiver. Kept tryin too bind same thing. So i connected to betaflight to see if it works n it does but jus keeps beeping. I have it connected as ppm n the...

Does anyone know how to connect the tbs crossfire to a flysky i6 transmitter cant find anything about it n says it'll go on any radio?

Ya when im soldering the wire to the pad im gonna make sure its melted n on whole pad. I cant change temp on soldering iron n its 400f it doesnt like alot of solder one pad had too much n wont melt n now i gotta desolder n redo. And i got another question my vtx that i got from another quad is...

Its obvious that with the advice from some questions ive asked around on forums that fc boards n other pcb boards that there alot more forgiving than i thought

Thought its stronger then paint to go over where i scratched the board through the black paint n looked like copper. I dont know much about electronics n the pads r so close n that scratch is in between a 5v n ground n know that if they touch itll cauze a short

Ya im a very detailed person i make custom exotic wood furniture builder where little detailz matter jus getting into electronics. Thnx i figured so but wasn't sure lol

I resoldered n im not using the small ground on top, gonna put vtx n cam ground on the bottom small pad n its not alot of flux on it after cleaning but is still there. Couldnt use a better pic of it cuz of the size

Thankz alot for all your advice, i desoldered the small solder pads to clean the flux off but i cant get all the stickyness off so is that ok is it conductive at all? I dont know alot about soldering i know how to thats easy for me but the pads being so close to each other. I tried to scratch...

So ive soldered a few pads on a f4 05 aio and theres flux around the outside and i want to clean it so it doesnt bridge or short anything but afraid to to use some kind of cleaner like rubbing alcohol, dont know if it will hurt anything on the board? Also is it ok to use the rubbing alcohol or...

K thnx man much appreciated

No im not talking about the esc power wires but with them its 5 n 4, most have jus 4 signal n ground then the power n ground. Im jus wondering about the ones that do have the signal ground n power then the esc power n ground do i need all 4 extra power wires going to rx or fc which i think is...

So im trying to reuse esc from a quad to my new build and theres 3 wires for wiring to receiver or fc. Do i need all red wires to goto receiver or to the fc most esc dont have the extra red wire cause i think its cause it has a bec to give power to rx or fc but dont know if i need all 4 conected.