First quadcopter ever

B

Brayhi

New Member
I am a new here I hope that I get helped

Years ago I like quadqopter so now I decided to build one what ever will happen even if it not working but I have to try so
Afterlife searching and looking Google utube I got some info how to do that but first what I need to find the combatible parts I read that bigener should start with 450 frame

After looking on bangood and Ali express i am going to choose those parts :

450 frame
4 motor 2212 1000kv I will buy one spare also
4 speed controller 20 or 30 a Simkon which are more sheaper than other also I will get one spare
Mini hub matek pdb
Spf3 or ominibus f4 or kk2.1 because I found that it's easy configuration kk
Fs-ia6b transmitter
Fs-ia6 receiver or fs-rb6
Lipo battery 11.1 2800 may 25c

Also some wiring connector

Plz help me if this parts will work with each other or I have to modify some parts
 
mozquito1

mozquito1

Well-Known Member
All will work. I wouldn't recommend the kk2. 1 though.. Bad gyro.
I also have the same Tx/rx.
The simonk esc's are a bit dated but run fine with just calibration, before everytime you go out or after say every 10 battery's. I've actually just orderd another 2 for my very first customer, who takes his 350 quad away on holiday. He owns a barge somewhere in the Midlands.
I think you could go a bit bigger on the battery 3000-4000mah as long as you are not flying acro.. Or zooming around.
Go for the 30amp esc.
There is no firmware update for them like the blheli have. All you need to do is a throttle calibration with them.
This is all basic stuff & we can help.
 
B

Brayhi

New Member
mozquito1 said:
All will work. I wouldn't recommend the kk2. 1 though.. Bad gyro.
I also have the same Tx/rx.
The simonk esc's are a bit dated but run fine with just calibration, before everytime you go out or after say every 10 battery's. I've actually just orderd another 2 for my very first customer, who takes his 350 quad away on holiday. He owns a barge somewhere in the Midlands.
I think you could go a bit bigger on the battery 3000-4000mah as long as you are not flying acro.. Or zooming around.
Go for the 30amp esc.
There is no firmware update for them like the blheli have. All you need to do is a throttle calibration with them.
This is all basic stuff & we can help.
Click to expand...
Thanks
I will take Ur advise and buy a one more battery 3000 may for the escs I know that is not a good asc but I just want my quad flying good and after that i want to build another one with complete fpv system and on that time I think I will buy an opto ESC
By the way the simkon escs have to connect all bec wire (signal -positive- grd)
Or connect only one bec and the other I should remove the red positive wire from bec
 
mozquito1

mozquito1

Well-Known Member
I would only connect 1 of them.
I don't know without checking if 4 would blow an F3. You could just strip all red wires & power it from the pdb, off the 5v bec to motor pin set 6 or 8 out the way of the signal wires on 1-4.
Will you use pins provided with board for plug & play or hard wire just to pin holes.
 
B

Brayhi

New Member
mozquito1 said:
I would only connect 1 of them.
I don't know without checking if 4 would blow an F3. You could just strip all red wires & power it from the pdb, off the 5v bec to motor pin set 6 or 8 out the way of the signal wires on 1-4.
Will you use pins provided with board for plug & play or hard wire just to pin holes.
Click to expand...
Is work if I just get 5v from pdb to flight control and then remove all the red wire from bec
 
You must log in or register to reply here.
Top