naze32 rev6

Hi All, This is my first post here so please be gentle. At the weekend I took my son flying with his ZMR250 self build, which has a naze 32 rev 6 full flight controller, a 20A all in one ESC (i know - horrible, but wanted his first build to be fairly simple for him), Matek PDB, and racerstar...

Hi guys, I just finished my ZMR250 build wiith naze rev 6 emax simonk 12a esc emax 2204 2300kv motors and DAL 6045 bullnose pprops. There is a problem i ordered the wrong battery, a 3300mah 35c 11.1v 3s lipo its 270 grams in weight i dont intend to use a camera or any other equipment so will it...

Guys please help! I am completely new to drone building. I have my first racer drone more a less finished. However, I'm trying to wire a old futaba R606Fs receiver to a new naze32 rev 6. Can this be done and if so can someone please explain the wiring to me. If not, is there a new receiver I can...

Guys please help! I am completely new to drone building. I have my first racer drone more a less finished. However, I'm trying to wire a old futaba R606Fs receiver to a new naze32 rev 6. Can this be done and if so can someone please explain the wiring to me. If not, is there a new receiver I can...

im running a naze 32 rev 6 with cleanflight and simonk 30A esc's. after i callibrated the esc's the motors wont spool as quickly but they still do, making the quad pitch forward or backwards. another thing ive noticed is that it will begin to spin at an exponential speed. i thought it might be...

Hi , I am new to the quadcopter thing and this is my first build all day I have been researching and trying to figure out to make this setup work( naze 32 rev6 with FS-R6B), I have nothing and I'm pretty desperate now I need someone to help me set this up, how to wire the receiver to the flight...

Good Day, today i finished the building process of my new quadcopter. Naze32 Rev6 Full S550 Frame 30A SimonK Esc 100KV Motors 1045 Props So the building part is done, all is neat and like i want. I started the calibration and the initial setup. Flashing Naze etc. I use a Turnigy 9xr...

Help! This is my first quadcopter build and I am having an issue where I unplug the usb cable from my Naze32 rev6 (I am using cleanflight) and when I try to do anything on my transmitter, nothing happens. There is just a solid blue light. I have been trying to get this thing to work for three...

I have the FS-i6 transmitter and I am trying to map it in Cleanflight. I am having quite a lot of trouble. I have read many other forums, none of which have worked. Currently I am mapping like this: 4ARTE123 AND I have all of the channels reversed on my RX. This gets everything correct except...

I have the Naze32 Acro Rev6 and a receiver that doesn't support any type of CPPM, only PWM. I also have servo leads (if they are needed). I can't seem to find how I can connect the 2 together. All of the tutorials seem to use CPPM. So, how can I connect my Naze32 Acro Rev6 to a PWM receiver?

Hello everyone, I have installed betaflight 2.8.0-RC3 on my naze32 rev 6. I have disabled oneshot, and have set a switch to arm and airmode. My pid numbers have been transferred over from the last firmware. However, upon arming, the motors throttle up and the quad starts climbing. The...

hi guys You'll have to forgive means I'm new to quads but have been building and flying helis and planes for years. I've just finished building my new zmr250 with a full naze32 rev6. I'm trying to work in my Spektrum dx6 with an r615x in rd ppm mode but I'm lost on how to work in the throw...