Search results

  1. B

    new quad version 4

    just finished my new quad (mark 4). its 400 x 350 mm with 10x4.5 props A2212/13T 1000kv motors 16 mm dia carbon tube arms (ally tube clamps plastic motor mounts) flat ally body with foam covered wire legs. CC3D and fleshy fs-i6 transmitter fsi6a receiver (for mow) weight without battery 649g...
  2. B

    Fs i6 afhds 2a connection to cc3d

    Hi All, I just gone and bought a new radio control, its a Flysky FS-i6 AFHDS 2A 2.4GHz 6CH (last controlled I dropped and now it won't work on the throttle it was a fs-ct6b) now how do I connect the receiver to the cc3d via the ibus connection what cable do I need ? also I see on youtube that...
  3. B

    next phase

    Hi all, I'm a happy bunny tonight, just finished my first build :) its 350mm square with 10*4.5 props 2212/t13 1000kv motors cc3d and 3500mah 3s battery all up weight inc batt 1001g :) my question is now I'm looking for a camera is there one i could use which will give two...
  4. B

    battery

    Hi all, Im looking for some batteries for my quad quad is 350mm square H frame running 4x 2212/13T 1000kv motors and a cc3d and 750g in weight are these any good 2X 3S 11.1V 6000mAh 40C Lipo Battery Deans Plug for RC Car Truck Airplane Hobby thanks mark..
  5. B

    servos

    Hi all, quick question thats not quad related. Im now building a flying wing type of drone (never built a flying plane before) and am looking for a pair of servos (I've used the regular rotating type before on boats) but space is a bit tight in this flying wing and i have found this type on...
  6. B

    cc3d and iPad

    Hi all, little question is there a app for the iPad to configger a cc3d for either librepilot or openpilot thanks
  7. B

    second new build

    Hi all, well i got sick of making balsa replacement arms, so made a new one verson 2.0 :) this time its out of plastic electrical conduit now it weighs 795g so slightly heaver here is the first flight
  8. B

    help again.:(

    Hi all, Im back again needing help, I have had a slight mishap with my quad. I went to pick the thing up and diss lodged one of the control cables from a ESC. to the cc3d (all 3 Power/ 0 volt / and signal) while the battery was connected and unit armed. now the motor won't turn it just...
  9. B

    cc3d 5 / 6 output help

    Hi all, can any one help, Im trying to get the 5/6 outputs on a cc3d to work but having no luck if i connects servo to the cc3d on output 5 or 6 it won't work but the quad will arm and fly. If i disconnect the receiver output 5 and 6 and connect the servo to the receiver the servo will work but...
  10. B

    help please

    Im after a little help, I was having a few issues with open pilot and was informed that librepilotd would help. so downloaded it to my mac and then to the cc3d, (including new firmware ) and now i have very little throttle control (its on full or off :( ) I've tried adjusting the throttle...
  11. B

    frame build

    Hi all, Now i have build my first quad out of balsa wood and am slowly getting the hand of crashing it sorry i mean flying it. i am now looking at building a better frame. Im building a H frame 450mm x 450mm and have two options 1) aluminium tube ( 15x15x1.5 mm walls) 2) carbon fibre 12mm round...
  12. B

    new frame

    Hi all, Now i have build my first quad out of balsa wood and am slowly getting the hand of crashing it sorry i mean flying it. i am now looking at building a better frame. Im building a H frame 450mm x 450mm and have two options 1) aluminium tube ( 15x15x1.5 mm walls) 2) carbon fibre 12mm...
  13. B

    First build

    Hi all, Here is my first build, I made the frame out of balsa (cos i had some :) and it easy to repair when i smash it) when i learn to fly i will make a new on out of carbon fibre. For now I'm running it on a tethered power supply (caravan 12v battery) need to save up for the charge and...
  14. B

    ESC advice

    Hi all, Im now about 1/2 way into building my first quadcopter, and am looking for ESC. what do you peeps recommend 1) 4 way esc lick this on eBay 401007394700 or 2) single esc for each motor. info on my build is in this post,new to quadcopter need advice thanks mark
  15. B

    new to quadcopter need advice

    Hi all, I total new to all this quadcopter fun, but had a go with a shop bought mini one a few week ago and now i think i have the bug. Now i like to build things (even when you could buy one) so i have made a list of parts, could you give us a nod if I'm on the right tracks. 1) flysky fs...
Top