Search results

I'm def sending them back. Mozquito I totally get what your saying about the motors. I don't understand it either. In blheli you can change the motor direction and the same thing happens. as soon as you take them off and put on the diatone motors or the brother hobby R4's, both quads work...

Oh and also.........not only does it do full yaw, when you give it just enough throttle to get off the ground, it instantly goes into full throttle

Ok update: I reset my flight controllers like you said. Just to see, I put my stock Diatone motors back on my Tyrant S and went outside and did a small hover test. The quad hovered perfectly and moved forward backwards and sideways correctly to my commands. I came inside, took the hypetrains...

Not sure what board reset is

Sorry for the late reply: So I tried everything suggested here. Some friends that have been into fpv also suggested the same things. I got into blheli and flashed the latest firmware (16.63 or 16.67 can't remember) and everything was successful. This was just on one of the two quads that was...

Thanks for the reply guys....I'm at work at the moment so as soon as I get home I will give y'all the pics and info you need. I just figured it was the motors cause any other motors I put on there works fine. But it does make sense how basic motors are that it would be something else. I'll...

Thanks for replying.....I'll def give your 2 suggestions a try and post back. I am under the impression that it is motor and not esc or FC just because after this problem I started taking both sets of my other motors and testing them both out on both sets of escs. They work fine no matter which...

Hi, I bought some Hypetrain motors that are doing something very strange. When you give the quad throttle and take off.....the quad just spins out of control as if you had full yaw counter clockwise. I made a video if you want to see what it does. . Go to :47sec if you just want to see...

Thanks for the replies guys. It may be a dud I have seen some of these reviews. But just to give it one more shot I want to hook it up properly. The camera is already getting power, grd, and signal from a JT plug on the FC. For the VTX should I just flip the board and solder to 5V, GRD, and...

Hi, I'm trying to figure out how to wire a regular 5V vtx up to Diatone Tyrant S that has a Diatone FuryF3 FC. The VTX is a DYS MI200. The original Diatone VTX is not required to only have 5V like this DYS is, and it was also installed and powered through a jt plug that sent VCC power to...

Thank you for the reply. I'm a super noob so after reading all that I might be more confused! On my flight controller my original vtx used this for power i believe (VCC). After trying a new vtx hooked up exactly the same way, the vtx would not power when the quad did. Is there a way of...

Hi guys i'm curious what VCC is on flight controller. What does it stand for and what does it do exactly? Thanks

Hi im installing a new DYS VTX on my Tyrant S. I just hooked up the 3 coords (1. 5v in 2. GND 3. AV in) to the cables coming from the FC. This is the same way that both the tyrant s original VTX and a TBS unify were plugged in and worked. When I turned on power after plugging up this DYS, I...

Ok thankyou all!!!!!!

Hi everyone, I'm about to make the jump on my first quad build and wanted to do the UAVfutures $99 build. The only thing I noticed is there is no OSD in this build and I'm really concerned about frying my batteries. Is there a way to know when to stop without OSD? I see other FC's that...

Hi everyone, I'm curious if my selection is everything I need to enter the gates of FPVvalhalla: 1) The Diatone Tyrant S (PNF) 2) The Turnigy Evolution 3) Aomway commander goggles 4) 4s batteries - Haven't picked out the brand yet My understanding is that with a PNF drone, I have to...