Search results

Here is what happen. I had a pixhawk from radiolink. Barometer went bad and their support wanted as much as a new one to fix the old one. I bought another pixhawk which was labeled pixhawk 2.4.8 on the unit. Using the same connections I had for the previous pixhawk from the minum osd I now do...

Good to know. Thank you for the great information.:)

I reviewed the logs and my drone did go into failsafe for a battery setting of 14V. I guess 7 min flight time is good for a 550 with a tarot gimbal with a gopro running a 4S 5200 battery.

I agree with it seems to be going into failsafe. The thing is I have failsafe set to go to RTL and not just to land. I was not monitoring OSD when this happened so not sure if it did show failsafe activated. I haven't checked yet this time but last time there was no entry in the logs showing...

This has happened twice. I activate RTL mode just to check it out. There was no issue happening on both occasions. I have RTL set on a separate channel /switch (channel 7) in mission planner. My other 6 modes are set using channel 5. After rearming and take off the drone initiates a landing mode...

Sorry for not being more clear. I have no issue setting up switches on my Tranis. Done it with other items on my quad. The issue is getting a 3 position switch to work with the video switcher.

When I got the switch I set it up using another receiver just to make sure it works. My last one did not so I wanted to be sure prior to installing it into my quad. As I said its not my connections or the switcher itself so the next variable is the channel set up hence the reason for asking for...

There must be others who use a Pixhawk with a video switcher. Not understanding why it's so difficult for step by step instructions. It's more then just assigning a switch on the radio. That's simple.

Using SBUS off the X8R so all the channels are through the pixhawk. I already have aux channel 9-11 being used to control gimbal and FPV camera servo. These movements are set to knobs on the tranis. From what I've read on other post you don't connect to the X8R when using a Pixhawk FC.

First let me say I've connected the switcher using a ubec feeding a X8R and 2 cameras and it switches between both no issue so I know my connections are correct. I move this over to my quad and connect to aux port 4(channel 12) on the pixhawk. Program my tranis radio mixer for channel 12 for a 3...

Seems there was some corrupted code. When I crashed the battery became disconnected. All I know is after reset parameters in MP to default and going through set up and calibrations all systems are working normally. When in doubt start fresh.

This is a weird one. I've had my drone working fine. Had a minor mishap. After fixing frame I'm not able to arm pixhawk 4 with Tranis 9D plus. I'm able to arm in mission planner and run motors with Tranis and also disarm with Tranis moving sticks to center. Moving the left stick down and to...

I configured a Usmile Beitian NEO-M8N GPS Module with Built-in HMC5883L Compass Protective Case for Ublox PX4 PIX APM2.5/2.6 Pixhawk using UCenter which went great. When I plug into a SP Racing F3 Deluxe FC using the Uart2 port my other SoftSerial ports become disabled along with Uart2 in...

I replied stating I discovered the issue and now have telemetry. Forgot to ARM the drone which allows telemetry to be sent.

My bad! Forgot to ARM the drone. I now have telemetry.

Yes. For Softserial 2, Using PPM.

I've watch numerous videos and setting up telemetry but still can't get working. This is what I have so far. Taranis 9D Plus D4R-II SP Racing F3 Deluxe I'm using the soft serial IO2 channel 6 running 1 wire to RX port on receiver. I've set up configuration in Cleanflight for Soft serial 2...