RENOV8R's Recent Activity

  1. RENOV8R replied to the thread TBS Unify Pro Mounting Board.

    Almost forgot, here's a link https://whitenoisefpv.com/products/rx-vtx-stack-mounting-board-tbs-unify-pro-v2-5v-frsky-x4r-d4r

    Jun 22, 2018 at 4:48 PM
  2. RENOV8R posted a new thread.

    TBS Unify Pro Mounting Board

    I like my builds to be neat and tidy, so it always irks me that I have to mount my video transmitter with sticky tape and zip ties....

    WhiteNoise 006.JPG WhiteNoise 009.JPG WhiteNoise 008.JPG WhiteNoise 010.JPG WhiteNoise 012.JPG

    Forum: Parts & Components

    Jun 22, 2018 at 4:43 PM
  3. RENOV8R replied to the thread Finally chosen my components, are these all compatible?.

    Oh, and you're Pixhawk is run by open source software/firmware called Ardupilot. Better read up...

    Jun 21, 2018 at 6:14 PM
  4. RENOV8R replied to the thread Finally chosen my components, are these all compatible?.

    Industry standards, they'll fit.

    Jun 21, 2018 at 6:08 PM
  5. RENOV8R replied to the thread Anticipation!.

    Initial programming and firmware updating takes quite a while, but you're going to love it! Did you get the fly more package with...

    Jun 21, 2018 at 6:03 PM
  6. RENOV8R liked Tentoes's post in the thread Anticipation!.

    A DJI Spark should arrive today or tomorrow. I'm expected to take pictures with it Saturday. Not much time for practice.

    Jun 21, 2018 at 6:01 PM
  7. RENOV8R replied to the thread Finally chosen my components, are these all compatible?.

    OSD works by taking flight information received from your flight controller and overlaying them onto your video image. A simple internet...

    Jun 21, 2018 at 5:55 PM
  8. RENOV8R replied to the thread Drone randomly over flips when rolling.

    Good advice from Moz especially dropping the setpoint weight but I'd do an update before you go any further. Your Configurator is 10.0,...

    Jun 21, 2018 at 3:42 PM
  9. RENOV8R replied to the thread Drone randomly over flips when rolling.

    Welcome to the forum! I think you're on the right track in thinking that you need to raise your D term some. I'm no expert on PID...

    Jun 20, 2018 at 9:35 PM
  10. RENOV8R attached a file to the thread Finally chosen my components, are these all compatible?.

    [ATTACH] Here's a basic diagram of a Pixhawk setup. Think you're up to this?

    pixhawk.jpg Jun 20, 2018 at 4:28 PM
  11. RENOV8R liked mozquito1's post in the thread Finally chosen my components, are these all compatible?.

    Go for the Naza.

    Jun 20, 2018 at 4:26 PM
  12. RENOV8R replied to the thread Finally chosen my components, are these all compatible?.

    Depends, what flight controller have you decided on?

    Jun 20, 2018 at 4:07 PM
  13. RENOV8R replied to the thread Finally chosen my components, are these all compatible?.

    Yes, I'm sure there are...........

    Jun 20, 2018 at 2:36 PM
  14. RENOV8R replied to the thread Finally chosen my components, are these all compatible?.

    No, the ESC does not force current into the motor, it just needs to be able to handle the current the motor is pulling. In fact, you...

    Jun 20, 2018 at 1:54 PM
  15. RENOV8R replied to the thread Finally chosen my components, are these all compatible?.

    You may be able to able to slightly increase your flight time by going with a 4S lipo. The biggest difference would be a noticeable...

    Jun 20, 2018 at 1:35 PM